Abstract:<p>The injection molding process is widely used for the mass production of plastic parts. However, as product designs become lighter, thinner and smaller, and the allowable tolerances shrink, the need to improve the quality consistency of the injection molding process has emerged as a critical concern. In mass production, injection molding is typically performed using fixed settings of the machine inputs. However, in practice, the properties of the plastic melt invariably change from batch to batch and even from shot to shot. Consequently, the use of fixed parameter settings fails to guarantee the stability of the molded part quality. Existing quality monitoring and control systems for the injection molding process are often based on pressure information. However, obtaining this information generally requires the installation of pressure sensors within the molding cavity, which is not only expensive and time-consuming, but may also interfere with the injection molding process itself. Accordingly, the present study proposes a quality monitoring and control system for injection molding processes based on the tie bar elongation measurements obtained using a strain gage. In the proposed approach, variations in the tie bar strain characteristic are taken to indicate deviations in the process stability and are used to manipulate the processing parameters accordingly in order to ensure the stability and consistency of the molded part quality. The feasibility of the proposed approach is demonstrated by performing injection molding trials with a two-cavity mold designed to produce tensile test specimens. The experimental results show that the quality of the molded parts varies significantly with the injection speed, velocity-to-pressure (V/P) switchover point, holding pressure, and melt temperature. Among these four parameters, the V/P switchover point and holding pressure induce a particularly rapid dynamic response, and thus provide an effective means of compensating for process deviations from shot to shot. By changing the melt temperature to simulate environmental noise, it is shown that the two parameter settings enable the consistency of the part weight to be restored to a range of 0.01 g within six shots. Moreover, the yield rate is enhanced from 60% to 90%.</p>

INJECTION MOLDING OF POLYCARBONATE THICK-WALLED PARTS USING A TOOL WITH VARIOUSLY DESIGNED GATE INSERTS

Study of Injection Molding Process to Improve Geometrical Quality of Thick-Walled Polycarbonate Optical Lenses by Reducing Sink Marks

Simulation and Experimental Study on Enhancing Dimensional Accuracy of Polycarbonate Light Guides

Research on the multilayer injection molding of thick-walled polymer optical products

Influence of Polymer Flow on Polypropylene Morphology, Micro-Mechanical, and Tribological Properties of Injected Part

Injection Molding of Polymers and Polymer Composites

Development of a Polyethylene Glycol/Polymethyl Methacrylate-Based Binder System for a Borosilicate Glass Filler Suitable for Injection Molding

Effect of Micro-Mold Cavity Dimension on Structure Andproperty of Polylactic Acid/Polycaprolactone Blend Undermicroinjection Molding Conditions

Effect of Micro-Mold Cavity Dimension on Structure and Property of Polylactic Acid/Polycaprolactone Blend under Microinjection Molding Conditions

Numerical Simulation and Process Optimization of a 3D Thin-Walled Polymeric Part Using Injection Compression Molding

The Injection Molding of Biodegradable Polydioxanone—A Study of the Dependence of the Structural and Mechanical Properties on Thermal Processing Conditions

Characterization of Stereolithography Printed Soft Tooling for Micro Injection Molding

Injection moulding of mechanical micro-manufactured structures for optically encoding plastic surfaces

Characterizations of polymer injection molding tools with conformal cooling channels fabricated by direct and indirect rapid tooling technologies

Review on Fabrication Technologies for Optical Mold Inserts

Injection Molding Process Simulation of Polycaprolactone Sticks for Further 3D Printing of Medical Implants

Quick-Delivery Mold Fabricated via Stereolithography to Enhance Manufacturing Efficiency

Enhancing the quality stability of injection molded parts by adjusting V/P switchover point and holding pressure

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene

Numerical Study of Thin-Walled Polymer Composite Part Quality When Manufactured Using Vacuum Infusion with Various External Pressure Controls

Surface Features of Polymer and Ceramic Microstructured Parts Manufactured by Micro Injection Molding