Abstract:Grouting materials require not only high ultra-early-stage strength of the stone body, but also proper working performances, such as high fluidity and fast setting time, as well as good stability. Compared with the traditional pure cement grout, geopolymer grouting material has the advantages of fast setting time, high fluidity, good slurry stability, and high early strength of the slurry stone body, which is beneficial to reuse solid waste resources and can be applied to the conditions of rapid construction or repair work to a certain extent. This paper presents an experimental investigation into the performance variation of geopolymer grouting material with varied mass fractions of raw materials, and the grouting performance of geopolymer material with optimal mix proportion is also presented. The study is implemented by employing the designed experimental schemes, focused on fluidity and setting times, as well as ultra-early-stage (4 h, 8 h, 12 h, 16 h, 20 h, and 24 h) mechanical strength. The experimental result demonstrates that both ground granulated blast-furnace slag (GGBS) content and the mass ratio of activator solution to solid have influence on the working performance of geopolymers, and both GGBS content and activator concentration have influence on the mechanical strength of geopolymers. Furthermore, the variance analysis demonstrates that the fluidity of geopolymer material is dominantly affected by the mass ratio of activator solution to solid, the setting time of geopolymer material is mainly influenced by GGBS content, and the mechanical strength of geopolymer material is mainly affected by activator concentration. Moreover, the recommended mix proportion of geopolymer grouting material is proposed in this study, in which the replacement rate of GGBS is 45%; the modulus and concentration of modified sodium silicate activator are 1.5 and 75%, respectively; and the mass ratio of activator solution to solid is 1.5. In the recommended mix proportion, the geopolymer material has excellent comprehensive performance to implement grouting operation, in which the compressive and tensile strengths of the stone body reach 12.2 MPa and 0.8 MPa in 4 h, and reach 21.2 MPa and 2.1 MPa in 24 h. The fluidity is 223 mm, the initial setting and final setting times are 50 min and 57 min, the slurry stability of geopolymer material is good without liquid precipitation, in which the setting time is far less than 2 h. This work provides the experimental foundations for investigating the performance of geopolymer grouting material, which is also expected to provide reference for the further application and promotion of geopolymer materials used for grouting operations in rapid construction or repair work.

Optimization of Composite Grouting Material Proportioning Based on Regression Analysis Method

Development and Evaluation of Physical and Mechanical Properties of Alkali-Activated Multi-Component Composite Grouting Materials

Optimization of Formula for Stabilizing Muddy Soil Using Response Surface Methodology

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

Mixture Optimization for Mechanical, Environmental, and Economic Objectives in Grouting Slurry for Repairing Earthen Sites

Development and application of new composite grouting material for sealing groundwater inflow and reinforcing wall rock in deep mine

Experimental Investigation of Synchronous Grouting Material Prepared with Different Mineral Admixtures

Study on Performance Optimization of Water-Rich Grouting Materials Based on Response Surface Methodology

Optimization on overall performance of Modified Ultrafine Cementitious Grout Materials (MUCG) and hydration mechanism analysis

Study on Slurry Flow Characteristics and Diffusion Law of Superfine Cement-Based Composite Grouting Material

Development and performance optimization of a new composite sealing material prepared by drilling cuttings

A Study on the Mix Proportion of Fiber-Polymer Composite Reinforced Cement-Based Grouting Material

Experimental Investigation on the Mix Proportion of Fiber-Reinforced Ultrahigh-Strength Grouting Material

Study on the Strength and Micro Characteristics of Grouted Specimens with Different Superfine Cement Contents

Study on the effect of mineral admixtures on working and mechanical properties of the grouting material

Performance Investigation of Geopolymer Grouting Material with Varied Mix Proportions

Multi-Response Optimization of Ultrafine Cement-Based Slurry Using the Taguchi-Grey Relational Analysis Method

Grouting Material Development and Dynamic Grouting Test of Broken Rock Mass

Optimization of Grouting Material Mixture Ratio Based on Multi-Objective Optimization and Multi-Attribute Decision-Making

Cement-based grouting material development and prediction of material properties using PSO-RBF machine learning

Study on properties of inorganic grouting material modified by ultrafine slag powder