Abstract:The performance of grouting materials directly affects the reinforcement effect of fractured rock masses by grouting. This paper investigates the synergistic effect of graphene oxide and fly ash on the properties of cementitious grout materials and the cementing effect of grouting reinforcement on broken rock masses. Basic performance tests such as flowability, bleeding rate, and setting time of grout slurries were conducted, and macroscopic characterization were tested for flexural strength, compressive strength, permeability and resistivity of the hardened grout paste. Direct shear tests of slurry-rock interfaces were performed using a self-made shear box, and the microstructures and mineral compositions of the slurry-rock interfaces were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The test results show that the flowability, bleeding rate, and initial setting time of graphene oxide and fly ash (GO-FA) cement-based grout slurries with a water-cement ratio of 0.8 are 413 mm, 4.8 %, and 12.7 h, respectively, indicating high flowability and stability. The 28-day flexural strength, compressive strength, and permeability of GO-FA the hardened grout paste are 4.6 MPa, 25.7 MPa, and 1.50 × 10 −9 cm/s, respectively, which are 28.5 %, 30.4 %, and 25.4 % higher than those of pure cement hardened grout paste. The electrical resistivity of the hardened grout pastes increases with the curing time of the slurry and eventually stabilizes, and a linear relationship between compressive strength and electrical resistivity is established. The reinforcement effect of GO-FA grout filling on broken rock masses is the best, with significantly increased peak shear strength and residual strength of the slurry-rock interface after grouting compared to traditional cement grout filling, indicating enhanced deformation resistance and a 19.8 % increase in cohesion. Grouting filling significantly improves the cohesion and internal friction angle of fractured rock mass interfaces, with the cohesion and internal friction angle of the slurry-rock interface after grouting filling with a thickness of 1 mm being 3.90 times and 1.28 times higher, respectively, than those of the unfilled fractured surface. The filling thickness has a significant effect on cohesion but little effect on the internal friction angle. The microstructure model of the slurry-rock interface is consistent with the Xie model, indicating the generation of hydration products such as calcium hydroxide and ettringite on the interface, as well as small amounts of potassium feldspar, kaolinite, and the new mineral component calcite.

Optimization of microfine-cement-based slurry containing microfine fly ash and nano-CaCO3 for microfracture grouting

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

Sedimentation-affected Engineering Performances and Microstructures of a Hybrid Portland- Sulfate Aluminate Cement Grout Cast in Long Tubes

Multi-Response Optimization of Ultrafine Cement-Based Slurry Using the Taguchi-Grey Relational Analysis Method

Research on Sustainable Development of Fine-Grained Material Cement Slurry

Optimization on overall performance of Modified Ultrafine Cementitious Grout Materials (MUCG) and hydration mechanism analysis

Study on Slurry Flow Characteristics and Diffusion Law of Superfine Cement-Based Composite Grouting Material

Experimental research on mechanical performance of grouting plugging material with large amount of fly ash

Workability and Mechanical Properties of Superplasticized Microfine Cement Grouts

Development and application of novel microfine cement-based grout

Development of High-Performance Microfine Cementitious Grout with High Amount of Fly Ash, Silica Fume, and Slag

Workability and mechanical properties of ultrafine cement based grout for structural rehabilitation: A parametric study on the partial replacement with SCMs

EXPERIMENTAL STUDY ON PROPERTIES AND MICROSTRUCTURE OF NANO MODIFIED ULTRAFINE CEMENT-BASED GROUTING MATERIAL

Study on the properties of graphene oxide cementitious grout materials and its cementing effect in reinforcing broken rock mass by grouting

Experimental investigation on the failure mechanism of grouted rock mass: Mesostructure and macroscopic mechanical behavior

Applying Novel Micro–Nano-Siliceous Grouting Material Improves Mechanical Behaviors of Fractured Rock Masses and Microscopic Characteristics of Slurry–Rock Interface: Experimental and Numerical Simulation Investigations

Study on the effect of mineral admixtures on working and mechanical properties of the grouting material

Study on the Strength and Micro Characteristics of Grouted Specimens with Different Superfine Cement Contents

Multi-Response Optimization of High-Performance Low-pH Grouting Materials by Using Taguchi-Based Grey Relational Analysis

Experimental Investigation of Synchronous Grouting Material Prepared with Different Mineral Admixtures

Experimental Study on the Influence of Content and Fineness of Fly Ash on the Mechanical Properties of Grouting Slurries