Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Mechanical performance of steel tubes filled with demolished concrete lumps under axial compression

Experimental Study on Axial Compressive Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Concrete-filled Steel Tubes with Reinforcing Bars or Angles under Axial Tension

Numerical Investigation on Compressive Performance of CFST Columns with Encased Built-Up Lattice-Angles

Experimental Studies On The Strength With High Slenderness Ratio Concrete Filled Steel Tubular Columns

Axial compressive behaviors of circular steel slag concrete‐filled steel tube slender columns

08.17: Experimental Behaviour of High‐strength Thin‐walled Concrete Filled Steel Tubular Stub Columns

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Axial compression performance of ultra-high-strength concrete filled steel tubular lattice short columns

Experimental and Numerical Study of the Behavior of Concrete-Filled High-Strength Steel Tube Columns with Large D/t Ratio under Axial Compression

Mechanical behavior and design applicability of ultra-high-performance concrete-filled circular steel tubular short columns under axial compression

Experimental and numerical studies of axially loaded square concrete‐encased concrete‐filled large‐diameter steel tubular short columns

Axial compression behavior of square section concrete-filled steel tubes reinforced with internal latticed steel angles

Axial Loading Behaviour of Self-Compacting Concrete-Filled Thin-Walled Steel Tubular Stub Columns

Performance of Special-Shaped Concrete-Filled Square Steel Tube Column under Axial Compression

Impact of D/t Ratio on Circular Concrete-Filled High-Strength Steel Tubular Stub Columns under Axial Compression

Performance of steel-reinforced square CFST stub columns loaded in axial compression: Experiments

Experimental behavior of concrete-filled double-skin tubular columns with outer galvanized corrugated steel tubes under axial compression

Bearing Strength of Concrete-Filled Steel Tube Reinforced with Internal Transverse Stiffened Bars under Axial Compression

Experimental Study on Axial Compression Performance of Thin-Walled Steel Tube Lightweight Concrete Columns With Composite Section

Experimental assessment on the size effects of circular concrete-filled steel tubular columns under axial compression