Abstract:In aero-engines, the shafts are supported on bearings that carry the radial and axial loads. A ball bearing is made up of an inner race, an outer race, and a cage, which contains the balls, these together comprise the bearing elements. The bearings require oil for lubrication and cooling. The design of the bearing studied in this work is such that the oil is fed to the bearing through holes/slots in the inner race. At each axial feed location, the oil is fed through a number of equispaced feedholes/slots but there are a different number of holes at each location. Once the oil has passed through the bearing, it sheds outward from both sides into compartments known as the bearing chambers. A number of studies have been carried out on the dynamics of bearings. Most of the analyses consider the contributions of fluid forces as small relative to the interaction of the bearing elements. One of the most sophisticated models for a cage–raceway analysis is based on the work of Ashmore et al. (2003, “Hydrodynamic Support and Dynamic Response for an Inner-Piloted Bearing Cage,” Proc. Inst. Mech. Eng. Part G, 217, pp. 19–28], where the cage–raceway is considered to be a short journal bearing divided into sectors by the oil feeds. It is further assumed that the oil exits from the holes and forms a continuous block of oil that exits outward on both sides of the cage–raceway. In the model, the Reynolds equation is used to estimate the oil dynamics. Of interest in this current work is the behavior of the oil and air within the space bounded by the cage and inner race. The aim is to determine whether oil feed to the bearing can be modeled as coming from a continuous slot or if the discrete entry points must be modeled. A volume of fluid (VOF) computational fluid dynamics (CFD) approach is applied. A sector of a ball bearing is modeled with a fine mesh, and the detailed simulations show the flow behavior for different oil splits to the three feed locations of the bearing, thus providing information useful to understanding oil shedding into the bearing chambers. This work shows that different flow behaviors are predicted by models where the oil inlets through a continuous slot are compared to discrete entry holes. The form and speed of oil shedding from the bearing are found to depend strongly on shaft speed with the shedding speed being slightly higher than the cage linear speed. The break-up pattern of oil on the cage inner surface suggests that smaller droplets will be shed at higher shaft speed.

Influence of the cage on the migration and distribution of lubricating oil inside a ball bearing

Experimental Study of Lubricant Distribution and Lubrication Enhancement Induced by Ball Bearing Cage

The Influence of Cage Pocket Lubrication on the Simulation of Deep Groove Ball Bearing Cage Motion

A Simulation Analysis of Ball Bearing Lubrication Characteristics Considering the Cage Clearance

Effects of Lubricant Viscosity-Temperature Relationship on the Capacity of Sliding Bearing

Investigation of Roller Bearing Cage Pocket Lubrication and Friction

Computational Fluid Dynamics Study of Oil Lubrication in Ball and Roller Bearings

Analysis of Oil-Air Two-Phase Flow Characteristics inside a Ball Bearing with Under-Race Lubrication

Interaction mechanisms between cage whirl motion, sliding of balls and vibration of bearing rings for angular contact ball bearings at various groove bottom circle diameters

Nonlinear dynamic model of ball bearings with elastohydrodynamic lubrication and cage whirl motion, influences of structural sizes, and materials of cage

Influence of Pocket Wear on the Dynamic Characteristics of High-Speed Ball Bearing Cage

Experimental Investigation of the Oil Supply Layer in a Model Rolling Bearing

Dynamic and Wear Characteristics of Self-Lubricating Bearing Cage: Effects of Cage Pocket Shape

Study on Distribution of Lubricating Oil Film in Contact Micro-Zone of Full Ceramic Ball Bearings and the Influence Mechanism on Service Performance

Experimental and Numerical Study of the Influence of Loading Direction on the Lubrication and Cooling of Self-Circulating Oil Bearing System Applied in Internal Gear Pumps

Effects of Cage Pocket Shapes on Dynamics of Angular Contact Ball Bearings

Analysis on Load Carrying Characteristics of Lubricating Film for Sliding Bearing Lubricated with Ferrofluid

Cylindrical roller bearing cage pocket lubrication

A Computational Fluid Dynamics Simulation of Oil–Air Flow Between the Cage and Inner Race of an Aero-engine Bearing

Experimental and theoretical approaches for determining cage motion dynamic characteristics of angular contact ball bearings considering whirling and overall skidding behaviors

Analysis of cage dynamic characteristics for high-speed full ceramic ball bearing under non-lubrication condition