Abstract:TiO2 and other semiconductor materials were found to have photocathodic protection effect for the metal coupled with these semiconductors film, as the potential of the metal shifted to a more negative value than its corrosion potential and the corrosion of the metal was prevented. TiO2 has been one of the most important semiconductors because of its good environmental friendliness and chemical stability. However, due to the wide band gap of TiO2 (3.2 eV) and the recombination of the photogenerated electron-hole (e–-h+) pairs, it can only absorb the light with the wavelength less than 380 nm, and it is hard to maintain the cathodic protection in the dark. In this paper, CdSe and other materials were applied to improve the photocathodic protection property. TiO2 nanotubes was prepared by anodization method, and CdSe was deposited on the TiO2 nanotube arrays by cyclic voltammetry method, and the optimum condition was selected from different cycles. The surface morphology and crystal phase of the composite was investigated by scanning electron microscopy (SEM), X ray diffraction (XRD) method. The photocathodic protection property of the composite material for 304 stainless steel in seawater was investigated by the electrochemical method including open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and the tafel polarization curves method. The experimental results showed that open circuit potential of 304 stainless steel decreased from -190mV to -500mV when the light was turned on, and the electrode potential slowly rises to about -250mV after the light was turned off. The composite material still could maintain the protective effect on stainless steel after the light was turned off. The work was supported by the Project of National Development and Reform Commission, the Nantong Science Project (BK2014008), and National Basic Research Program of China (2014CB643304).

Preparation of Ni-TiO2 Composite Coatings on Q390E Steel by Pulse Electrodeposition and their Photocatalytic and Corrosion Resistance Properties

Electrochemical Corrosion Behavior of Ni–TiO2 Composite Coatings Electrodeposited from a Deep Eutectic Solvent-Based Electrolyte

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Mechanical and Corrosion Resistance Properties of Tio2 Nanoparticles Reinforced Ni Coating by Electrodeposition

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Preparation and Corrosion Properties of TiO2-SiO2-Al2O3 Composite Coating on Q235 Carbon Steel

Corrosion and wear resistance of TiN/TiO2 composite ceramic coatings deposited by supersonic arc spraying

Preparation and properties of Ni-W-P-TiO2 nanocomposite coatings developed by a sol-enhanced electroplating method

The Influence of Pulse Plating Parameters on the Structure and Corrosion Behavior of Ni-W-TiC Nanocomposite Coatings

Preparation of Ni-P-Ti3C2Tx-Ce composite coating with enhanced wear resistance and electrochemical corrosion behavior on the surface of low manganese steel

Design an Epoxy Coating with TiO2/GO/PANI Nanocomposites for Enhancing Corrosion Resistance of Q235 Carbon Steel

High-temperature Oxidation of Electrodeposited Ni-Co-SiC Composite Coatings

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Photocathodic Protection of TiO2 Composite Material on 304 Stainless Steel

Electrochemical Synthesis of Ni/TiO2 Composite Coatings from Deep Eutectic Solvent and Electrocatalytic Characteristics of Deposits

Improvement of the Tribological Properties and Corrosion Resistance of Epoxy–PTFE Composite Coating by Nanoparticle Modification

Corrosion and wear resistance behaviors of electroless Ni–Cu–P–TiN composite coating

Core–Shell Spheroid Structure TiO2/CdS Composites with Enhanced Photocathodic Protection Performance

Relationship Between the Structure and Hydrophobic Performance of Ni–TiO2 Nanocomposite Coatings by Electrodeposition

TiO2‐epoxy nanocomposites coated steel: Surface morphology, spectroscopic, and photocatalytic characteristics

Titanium Dioxide–nickel Oxide Composite Coatings: Preparation by Mechanical Coating/thermal Oxidation and Photocatalytic Activity