Abstract:The simultaneous application of new low-NOx emissions standards and greenhouse gas (GHG) rules has placed great pressure on the commercial vehicle industry and has driven demand for innovative solutions. One potential solution, gasoline compression ignition (GCI), utilizes gasoline’s lower reactivity to promote partially premixed combustion and extract efficiency while reducing the PM-NOx trade-off curve. Gasoline’s volatility allows for the use of higher levels of exhaust gas recirculation (EGR), a key enabler of GCI combustion. In order to deliver higher levels of EGR while maintaining sufficient boost pressure, a tailored and efficient air-handling system is critical. This work presents the analysis-led development of a low-NOx GCI air-handling system including both turbocharger matching and EGR configuration for a prototype heavy-duty GCI engine based on a model year 2013 Cummins ISX diesel engine using low octane gasoline (RON80). In the analysis-driven development process, a 1D engine system-level analysis was closely coupled with closed-cycle 3D CFD GCI combustion development. Three different boost systems were investigated using a validated 1D engine model: 1) the production turbocharger; 2) an off-the-shelf single-stage waste-gate turbocharger; 3) a prototype single-stage variable geometry turbocharger. For each boost system, three EGR configurations were evaluated: 1) a high-pressure EGR route; 2) a low-pressure EGR route; 3) a dual-loop EGR route. The air-handling system performance was first investigated over five steady-state engine operating conditions extracted from the ramped modal cycle supplemental emissions test. Then, through cosimulation using a Simulink-based engine controls model, the best performing candidates under transient operation through the Heavy-Duty Federal Test Procedure certification cycle were identified. The production turbocharger, designed for 4–6 g/kWh engine-out NOx, suffered from low combined turbocharger efficiency under the low-NOx GCI thermal boundary conditions. The prototype 1-Stage variable geometry turbocharger, when used with a high-pressure EGR configuration, demonstrated higher combined efficiencies, while the waste-gate turbocharger showed the best results when used with a dual-loop EGR system. All low-pressure only EGR configurations were found to incur additional pumping penalties due to the need for a back pressure valve to drive sufficient EGR levels. In the transient test cycle analysis, the single-stage high-pressure EGR system was capable of delivering the target boost and EGR, while the off-the-shelf waste-gate turbocharger, with its higher mass inertia, showed slower turbine response and a resulting lag in boost response. Unsurprisingly, the dual-loop EGR system also suffered from delays in EGR delivery during engine acceleration. In summary, the prototype single-stage variable geometry turbocharger with a high-pressure EGR system produced the best performance over both the steady-state and transient engine cycles and was identified as the best candidate for the prototype low-NOx heavy-duty GCI engine.

Burner based thermal management approach utilizing in-exhaust burner technology with a CDA equipped engine

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

Methodology to Determine the Fast Burn Period Inside a Heavy-Duty Diesel Engine Converted to Natural Gas Lean-Burn Spark Ignition Operation

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

Fuel Consumption and Emission Reduction for Non-Road Diesel Engines with Electrically Heated Catalysts

Evaluation of thermal management technologies for fuel efficient cold-start emissions reduction in diesel engines

Diesel Engine 2-Stroke Breathing for Aftertreatment Warm-Up

Modeling Heavy-Duty Engine Thermal Management Technologies to Meet Future Cold Start Requirements

Exploring alternative combustion control strategies for low-load exhaust gas temperature management of a heavy-duty diesel engine

Effect of a Plasma Burner on NOx Reduction and Catalyst Regeneration in a Marine SCR System

Tailored Air-Handling System Development for Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Implementing variable valve actuation on a diesel engine at high-speed idle operation for improved aftertreatment warm-up

Variable valve actuation–based combustion control strategies for efficiency improvement and emissions control in a heavy-duty diesel engine

An experimental investigation of the combustion process and the injection strategy of a heavy-duty diesel engine equipped with a common rail fuel injection system

Exploring the NOx Reduction Potential of Miller Cycle and EGR on a HD Diesel Engine Operating at Full Load

Enhanced Exhaust after-Treatment Warmup in a Heavy-Duty Diesel Engine System via Miller Cycle and Delayed Exhaust Valve Opening

Study on Burner Type Diesel Particulate Filter System Using Compressed Air from Turbocharger

Experimental Study and Model Predictive Control of a Lean-Burn Gasoline Engine Coupled With a Passive Selective Catalytic Reduction System

Cold Start HD FTP Test Results on Multi-Cylinder Opposed-Piston Engine Demonstrating Rapid Exhaust Enthalpy Rise to Achieve Ultra Low NOx

An Experimental and Computational Investigation of Tailor-Developed Combustion and Air-Handling System Concepts in a Heavy-Duty Gasoline Compression Ignition Engine

A Study on the Compound Regeneration Control Strategy for DPF Using Burner and DOC