Abstract:The advent of new materials and technologies in building materials has changed the way of building. New lighter materials with easier application methods and improved mechanical behaviors, have become necessary for the market. Moreover, the new environmental policy (2022) aims to transform the waste management into sustainable materials management to ensure the long-term protection and improvement of the environment. For the brick and tile industry, raw materials and the additives that compose the product mixture seem to be a key factor in this direction. Furthermore, every product type (solid or perforated brick) requires different additives to achieve the properties that are postulated by the international standards. For the study, the wide range of additives that were used have been assorted into three (3) categories: the inert materials, the lightweight materials, and the industrial remains. Totally, eight (8) different materials were used as additives into ceramic mass, in different proportions each time. Almost all additives used for this research were pore-forming agents. These burn out almost completely before reaching the full-fire temperature, and do not change the fired body. As a result of additives burnt out, the necessary pore volume is formed in the fired brick body, which, if combined with an appropriate percentage of voids, result in raw density readings. The pore structure is significant as long as the ultimate strength of lightweight bricks is acceptable. In this study, additives between 3 and 25% by weight were added to the clay mixture. The extrusion of specimens in solid form was carried out using the Laboratory’s vacuum press. Firstly, the extrusion of specimens from the original raw material was implemented. Secondly, it was made on the material mixed with the additives mentioned above. A series of experimental activities were followed to determine the variations of the mechanical and physical properties as well as their production procedures (extrusion, drying, and firing). According to five (5) key properties measured in the current study and compared with the mixture without additives, it was found that the variation in thermal conductivity improvement is between -11% and 19%. The bending strength of the fired products showed a decrease from 16% to 55% except for the addition of bauxite residue, which increased the strength by 8%. Bigot drying sensitivity decreased from 11% to 27%. The density in two cases increased from 2% to 7% while in the majority the mixtures with the additives showed a decrease in density from 1% to 14%. Finally, the addition of the necessary water for shaping during extrusion showed a variation from a 10% decreased to a 14% increased water.

Developing lightweight concrete bricks by replacing fine aggregate with vermiculite: a regression analysis prediction approach

An Experimental Investigation of Mechanical Properties in Clay Brick Masonry by Partial Replacement of Fine Aggregate with Clay Brick Waste

Mechanical properties optimization and cost analysis of agricultural waste as an alternative in brick production

Soft computing techniques for predicting the properties of raw rice husk concrete bricks using regression-based machine learning approaches

Machine learning optimization of bio-sandcrete brick modelling using response surface methodology

Development of green concrete using effective utilization of autoclaved aerated concrete brick trash as lightweight aggregate

PHYSICAL AND MECHANICAL PROPERTIES OF SYNTHETIC BRICK FROM CEMENT MORTAR, RECYCLED POLYVINYL CHLORIDE AND GLASS FIBER

Analysing the Effectiveness of Municipal Wastewater Sludge, Bagasse Ash, Rice Husk Ash and Plastic Waste Powder for Manufacturing Bricks

Fresh and hardened properties of concrete made with recycled brick aggregate

EXPERIMENTAL INVESTIGATION ON CELLULAR LIGHT WEIGHT CONCRETE BLOCK USING IRONITE POWDER FOR REPLACEMENT OF CEMENT

Analysis of chemical-mineralogical content of brick waste as a pozzolan substitute material in blended cement

Efficient Recovery of Solid Waste Units as Substitutes for Raw Materials in Clay Bricks

Developing fired clay bricks by incorporating scrap incinerated waste and river dredged sediment

Evaluation of mechanical properties of cement mortars containing pond ash as partial replacement of river sand and prediction of properties by regression models

Use of waste brick as a partial replacement of cement in mortar

Towards a better living environment-compressive strength and water absorption testing of mini compressed stabilized earth blocks and fired bricks

Investigation study data to develop sustainable concrete mix using waste materials as constituents

Dematerialization of Concrete: Meta-Analysis of Lightweight Expanded Clay Concrete for Compressive Strength

Study on preparation of brick blocks by using construction waste and sludge

Stochastic Investigation into the Heterogeneity of Multiwalled Carbon Nanotube Infused Clay Bricks

An investigation of various properties of hybrid bricks using Natural fibers and waste fiber-based materials