The Tensile Properties of Recycled Polypropylene Filament (rPP) as 3D Printing Material

Boby Rusdyanto,Fitrian Imaduddin,Ubaidillah,Dody Ariawan

DOI: https://doi.org/10.5109/6782152

2023-03-01

Evergreen

Abstract:Online Public Access Catalog

What problem does this paper attempt to address?

Glass Powder Additive on Recycled Polypropylene Filaments: A Sustainable Material in 3D Printing

Ruben Bayu Kristiawan,Boby Rusdyanto,Fitrian Imaduddin,Dody Ariawan

DOI: https://doi.org/10.3390/polym14010005

IF: 5

2021-12-21

Polymers

Abstract:This study aimed to characterize the effect of a glass powder additive on recycled polypropylene (rPP) materials from food packaging to be used as filaments in material extrusion (MEX) 3D printing applications. The composite filaments studied were rPP filaments with glass powder (GP) additive in the 2.5%, 5%, and 10% fractions. As a baseline, the filaments made of pure virgin PP and rPP without additive were used. The filament that has been successfully made is then printed into a tensile test specimen and an impact test to observe its mechanical properties. Fourier-transform infrared spectroscopy (FTIR) characterization was also carried out to determine the effect of chemical bonding and thermal characterization using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of FTIR characterization on the sample rPP + 10% do not show a typical peak shift of PP, but give rise to new peaks at wavenumbers of 1000 cm−1 (Si-O-Na), 890 cm−1 (Si-H) and 849 cm−1 (O-Si-O), which indicate the typical peaks of the glass constituent compounds. In the thermal characteristics, the addition of GP shows the improved stability of mass changes to heat and increases the melting temperature of rPP. The ultimate tensile strength and Young’s modulus for rPP-based specimens with 10% GP additive showed an increase of 38% and 42% compared to PP specimens. In addition to the improved mechanical strength, the addition of GP also reduces the bending deformation, which can be well controlled, and reduces curvature, which is a problem in semicrystalline polymer-based filaments.

polymer science
The Mechanical and Physical Properties of 3D Printing Filament made from Recycled Polypropylene and Ground Tyre Rubber Treated with Alkali

Yusliza Yusuf,Nuzaimah Mustafa,Yusra Fitri Yusoff,Dwi Hadi Sulistyarini

DOI: https://doi.org/10.47836/pjst.32.s2.10

2024-06-14

Abstract:When molten, used vehicle tyres are unable to decompose or be recycled. Despite global efforts to find new uses for these materials, many worn tyres are still dumped in landfills. Therefore, this study proposes using ground tyre rubber (GTR) as a fill material for recycled polypropylene 3D printing filament. The filament composite’s physical and mechanical properties will be assessed in this investigation. GTR is expected to give the filament elastic characteristics, which could lead to rubber-like filaments. This study filled recycled polypropylene (rPP) polymer matrix composites with GTR to make filament. The mechanical and physical properties of a 3D-printed specimen made from rPP and GTR filament with varying compositions were analysed. Compared to pure rPP, rPP/GTR samples with 3 wt% GTR had a maximum tensile strength of 716.76 MPa. The flexural test findings showed that rPP/GTR with 3 wt% GTR had the highest flexural strength at 80.53 MPa, followed by rPP/1 wt% GTR at 65.38 MPa. In physical tests, the rPP/GTR at 5 wt% GTR had the highest water absorption at 5.41 %, and the wt% of GTR connected directly with water absorption. This study has shown that affordable, environmentally friendly rPP/GTR filaments can be developed with less amount of GTR content (3 wt%) and used for 3D printing applications, helping to lessen the impact of plastic and waste while having valuable mechanical and physical properties that are comparable to those of the pure polypropylene material produced.
Material Characterizations of the Polymers Reinforced with Recycled Flexible Plastic Blends as Filament for 3D Printing

Nur Nazira Alias,Ireana Yusra Abdul Fatah,Yew Been Seok,Sharifah Hanis Yasmin Sayid Abdullah,Amir Hussain Bhat,Saiful Bahri Mohd Diah

DOI: https://doi.org/10.37934/araset.37.1.115

2024-01-09

Journal of Advanced Research in Applied Sciences and Engineering Technology

Abstract:The high consumption of single-use plastics and the low recycling rates have seriously polluted the soil and ocean environments. Thermoplastic materials from recycling can be used to make filaments for 3D printing. This study is focused on preparing, characterizing, and comparing the polymers reinforced with recycled flexible plastic blends to be used as a filament in additive manufacturing. In this regard, two types of polymers were used to create the filament: High-Density Polyethylene (HDPE) and Polypropylene (PP), which were mixed with recycled flexible plastic (RF). The mixture was initially used to create filament by using a single extrusion machine, with various ratios of virgin HDPE and PP to recycled flexible plastic (in weight%) at temperatures of 190°C and 230°C. Then, the filament blends were characterized using infrared (IR) spectroscopy, thermogravimetric analysis (TGA), and field emission scanning electron microscopy (FESEM). TGA analyses revealed that RF can increase the thermal stability of V- HDPE and V-PP upon blending, and HDPE/RF blends show a higher decomposition temperature than PP/RF. FESEM indicated that adding 30% RF is the best percentage for both polymer blends where the structure appears ductile. It can be concluded that the HDPE 70% blend is suitable for 3D printer filament as it showed the best decomposition temperature and the ductility of the fracture structure, which meet the requirements for 3D printer filament.
Recycled polypropylene blends as novel 3D printing materials

Nicole E. Zander,Margaret Gillan,Zachary Burckhard,Frank Gardea

DOI: https://doi.org/10.1016/j.addma.2018.11.009

IF: 11

2019-01-01

Additive Manufacturing

Abstract:Consumer-grade plastics can be considered a low-cost and sustainable feedstock for fused filament fabrication (FFF) additive manufacturing processes. Such materials are excellent candidates for distributed manufacturing, in which parts are printed from local materials at the point of need. Most plastic waste streams contain a mixture of polymers, such as water bottles and caps comprised of polyethylene terephthalate (PET) and polypropylene (PP), and complete separation is rarely implemented. In this work, blends of waste PET, PP and polystyrene (PS) were processed into filaments for 3D printing. The effect of blend composition and styrene ethylene butylene styrene (SEBS) compatibilizer on the resulting mechanical and thermal properties were probed. Recycled PET had the highest tensile strength at 35 ± 8 MPa. Blends of PP/PET compatibilized with SEBS and maleic anhydride functionalized SEBS had tensile strengths of 23 ± 1 MPa and 24 ± 1 MPa, respectively. The non-compatibilized PP/PS blend had a tensile strength of 22 ± 1 MPa. PP/PS blends exhibited reduced tensile strength to ca. 19 ± 1–3 MPa with the addition of SEBS. Elongation to failure was generally improved for the blended materials compared to neat recycled PET and PS. The glass transition was shifted to higher temperatures for all of the blends except the 50–50 wt. % PP/PET blend. Crystallinity was decreased for the blends, but was highest in the 75–25 wt. % PP/PS and the 50-50 wt. % PP/PET blend with SEBS-maleic anhydride. Solvent extraction of the dispersed phase revealed polypropylene was the matrix phase in both the 50–50 wt. % PP/PET and PP/PS blends.

engineering, manufacturing,materials science, multidisciplinary
Development and Characterization of Rice Husk and Recycled Polypropylene Composite Filaments for 3D Printing

Maria A. Morales,Cindy L. Atencio Martinez,Alejandro Maranon,Camilo Hernandez,Veronique Michaud,Alicia Porras,Maria Morales,Cindy Atencio Martinez

DOI: https://doi.org/10.3390/polym13071067

IF: 5

2021-03-28

Polymers

Abstract:Nowadays the use of natural fiber composites has gained significant interest due to their low density, high availability, and low cost. The present study explores the development of sustainable 3D printing filaments based on rice husk (RH), an agricultural residue, and recycled polypropylene (rPP) and the influence of fiber weight ratio on physical, thermal, mechanical, and morphological properties of 3D printing parts. Thermogravimetric analysis revealed that the composite’s degradation process started earlier than for the neat rPP due to the lignocellulosic fiber components. Mechanical tests showed that tensile strength increased when using a raster angle of 0° than specimens printed at 90°, due to the weaker inter-layer bonding compared to in-layer. Furthermore, inter layer bonding tensile strength was similar for all tested materials. Scanning electron microscope (SEM) images revealed the limited interaction between the untreated fiber and matrix, which led to reduced tensile properties. However, during the printing process, composites presented lower warping than printed neat rPP. Thus, 3D printable ecofriendly natural fiber composite filaments with low density and low cost can be developed and used for 3D printing applications, contributing to reduce the impact of plastic and agricultural waste.

polymer science
Short basalt fibre reinforced recycled polypropylene filaments for 3D printing

Pouyan Ghabezi,Tomas Flanagan,Noel Harrison

DOI: https://doi.org/10.1016/j.matlet.2022.132942

IF: 3

2022-11-01

Materials Letters

Abstract:Additive Manufacturing (3D Printing, and specifically Material Extrusion) is a rapid and convenient manufacturing method using raw material in filament form and is a potential candidate process for the use of recycled plastics and fibres gathered from industrial waste and domestic recycling. In this research, off-cuts of basalt fibre and recycled mushroom trays made of Polypropylene (PP) have been collected, recycled and combined in an extruder to make short fibre reinforced filaments as material extrusion feedstock filament material. A Noztek Touch Dual PID filament maker was utilized to make reinforced PP with 0%, 2%, 5%, and 8% basalt fibre weight fractions. The extruding parameters including motor speed, heating temperatures, cooling fan status, extrusion tension have been optimized to produce a filament made from these waste materials with the desired surface quality, void content, and profile. Microscopic assessment has been carried out to verify the fibre dispersion and above mentioned quality measures in the upcycled filaments. Differential scanning calorimetry has been done to measure the melting and crystallization temperatures of collected polypropylene and recycled filaments, and the tensile strength and elastic modulus of the reinforced recycled polypropylene have been measured in presence of different percentages of short basalt fibres with 4.5 mm length. The produced filaments with 5% wt. of basalt are a good candidate for use as feedstock in manufacturing using 3D printing.

materials science, multidisciplinary,physics, applied
Optimization of Glass-Powder-Reinforced Recycled High-Density Polyethylene (rHDPE) Filament for Additive Manufacturing: Transforming Bottle Caps into Sound-Absorbing Material

Sarah Iftin Atsani,Swee Leong Sing

DOI: https://doi.org/10.3390/polym16162324

IF: 5

2024-08-18

Polymers

Abstract:Additive manufacturing presents promising potential as a sustainable processing technology, notably through integrating post-consumer recycled polymers into production. This study investigated the recycling of high-density polyethylene (rHDPE) into 3D printing filament, achieved by the following optimal extrusion parameters: 180 °C temperature, 7 rpm speed, and 10% glass powder addition. The properties of the developed rHDPE filament were compared with those of commonly used FDM filaments such as acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) to benchmark the performance of rHDPE against well-established materials in the 3D printing industry, providing a practical perspective for potential users. The resulting filament boasted an average tensile strength of 25.52 MPa, slightly exceeding ABS (25.41 MPa) and comparable to PLA (28.55 MPa). Despite diameter fluctuations, the filament proved usable in 3D printing. Mechanical tests compared the rHPDE filament 3D printed objects with ABS and PLA, showing lower strength but exceptional ductility and flexibility, along with superior sound absorption. A life cycle analysis underscored the sustainability advantages of rHDPE, reducing environmental impact compared to conventional disposal methods. While rHDPE falls behind in mechanical strength against virgin filaments, its unique attributes and sustainability position it as a valuable option for 3D printing, showcasing recycled materials' potential in sustainable innovation.

polymer science
The Properties of Glass Fiber Reinforced Polypropylene Filaments Recycled from Fishing Gear

Garrett Russell

2024-09-18

Abstract:Plastic pollution, mainly from lost fishing gear composed of high-density polyethylene (HDPE) and polypropylene (PP), poses a significant environmental obstacle. This study evaluates the potential of recycling PP from fishnet/rope and reinforcing it with glass fiber (GF) in the form of 3D printer filaments as a way to reduce/prevent ocean plastic. Two materials, one virgin (vPP-GF) and one made up of recycled polypropylene and virgin glass fibers (rPP-GF), were analyzed using differential scanning calorimetry, tensile, and Charpy impact tests. From the results, it was found that rPP-GF often outperformed vPP-GF. rPP-GF had a higher melting and crystallization point, likely a higher crystallinity, and could withstand a higher tensile stress, while vPP-GF could withstand a higher tensile strain. Further analysis revealed the potential presence of HDPE within the rPP-GF composite, which was not reported by the manufacturer. This significantly affected the Charpy test and made it difficult to draw conclusions from the resulting data. Nevertheless, their comparability in terms of mechanical and material properties indicates the strong potential of recycling polypropylene fishnet/rope and reinforcing it with glass fibers to extend their lifespan and reduce ocean plastic.

Soft Condensed Matter,Materials Science
Development and characterization of sustainable 3D printing filaments using post-consumer recycled PET: processing and characterization

Ch Kapil Ror,Sushant Negi,Vishal Mishra

DOI: https://doi.org/10.1007/s10965-023-03742-2

IF: 3.061

2023-08-17

Journal of Polymer Research

Abstract:In recent times, FDM technology has been extensively utilized to reuse small-scale thermoplastic waste materials to produce 3D-printed structures for various engineering applications. However, recycled material such as PET (i.e., waste from beverage bottling) for 3D printing is less explored because of poor mechanical properties due to possible thermal degradation, uncontrolled crystallinity, and shrinkage issues during high fusion temperatures. Hence, the aim of this study is to develop high-quality filament from PET waste for 3D printing purpose. This study involves the investigation of rheological, chemical, thermal, and mechanical behavior of PET filaments produced by different grades of PET plastic waste. The results indicated that filament made from recycled PET (RPET) water bottles and RPET soda bottles have comparable results with virgin PET (VPET) filament samples. The tensile modulus, yield strength, ultimate tensile strength, and tensile strain at break for RPET water bottle and RPET soda bottle made filament are 1932.78 MPa, 47.51 MPa, 52.44 MPa, and 98.86%; and 2009.66 MPa, 43.08 MPa, 46.08 MPa, and 7.46%, respectively. The novel filament produced from PET plastic waste has the capability to replace VPET filaments for fabricating high-quality structural parts through an additive manufacturing approach.

polymer science
Recycling polypropylene from non-woven disposable masks in developing a three-dimensional printing filament

Meng Zhang,Sarina Sun,Jun Liu,Jianzhong Sun

DOI: https://doi.org/10.1177/00405175221147722

IF: 2.3

2023-01-08

Textile Research Journal

Abstract:Textile Research Journal, Ahead of Print. Non-woven disposable masks play a unique role in reducing the COVID-19 pandemic threat in transmission between people, but the huge amount of disposable non-woven masks generated every day are currently posing a serious challenge to our environment on a global-wide scale. In line with this emerging problem, a series of recycling processes were designed and conducted to evaluate the performance of material recovered from those waste masks for potential use in three-dimensional (3D) printing. A composite filament from recycled polypropylene (rPP) and an additive material, glass fiber (GF), was fabricated by melt-blending processing followed by single-screw extrusion. A variety of material properties, including the chemical/mechanical/microstructure property, thermal stability, printability, rheology performance, and geometrical accuracy toward GF/rPP composite filaments, were comprehensively analyzed. Our results demonstrated that two important mechanical properties, the compression strength and the tensile strength, to a 3D printed object by fused deposition modeling (FDM) from the GF/rPP composite were significantly higher than that of a FDM 3D printed object from GF/polypropylene composites. The specific warpage parameter (Wsp) and the surface roughness (Sa) for a 3D printed object from the GF/rPP composite at 30 wt% GF additive would have printing accuracy of 0.54% ± 0.0014 and 21.1 ± 0.76 μm, respectively, and no clogging phenomenon was observed in the printer nozzle channel during the printing processing, suggested that this recycling method for a large number of non-woven waste masks was potentially applicable in serving as a FDM 3D printing material.

materials science, textiles
3D printing of polypropylene using the fused filament fabrication technique

A. F. Silva,O. S. Carneiro,R. Gomes

DOI: https://doi.org/10.1063/1.5008040

2017-01-01

AIP Conference Proceedings

Abstract:This work addresses the potential of polypropylene, neat (PP) and reinforced with short glass fibers (GRPP), as a candidate for the Fused Filament Fabrication (FFF)-based 3D printing technique. The entire production chain was evaluated, i.e., starting with PP and GRPP pellets, filaments were produced by extrusion and test samples were printed in different process conditions (different layers’ thicknesses, deposition orientation and infill) with the in-house produced filaments. This strategy enabled a true comparison between parts printed (FFF) with parts manufactured by compression molding (CM), using exactly the same grade of raw material.
Designing 3D printable polypropylene: Material and process optimisation through rheology

M. Bertolino,D. Battegazzore,R. Arrigo,A. Frache

DOI: https://doi.org/10.1016/j.addma.2021.101944

IF: 11

2021-04-01

Additive Manufacturing

Abstract:<p>A polypropylene-based material has been formulated to be suitable for fused deposition modelling (FDM). In fact, the high volumetric shrinkage and the rheological behaviour are main problems whereby polypropylene (PP) is not commonly used as a 3D printing filament. Experimental results have evidenced how material modifications have a strong impact on rheological behaviour, providing critical features that permit and improve material printability. An optimised 20 wt.% talc filled heterophasic PP copolymer has been developed. The peculiar properties of the materials have been assessed by thermal characterisation and rheological analysis. Several process parameters (extrusion temperature, screw speed, cooling conditions) have been evaluated in order to obtain a proper filament. Finally, a model part has been printed using different settings to check printing quality by morphological analysis.</p>

engineering, manufacturing,materials science, multidisciplinary
Development of 3D printing short carbon fiber reinforced polypropylene composite filaments

Bandar Almeshari,Bandar Almeshari,Harri Junaedi,Muneer Baig,Abdulhakim Almajid,Abdulhakim Almajid

DOI: https://doi.org/10.1016/j.jmrt.2023.02.198

IF: 6.267

2023-05-01

Journal of Materials Research and Technology

Abstract:In this study, the 3D printing short carbon fiber (SCF) reinforced polypropylene (PP) composite filament was developed. The micro-size SCFs were mixed with PP granules and extruded in a twin screw extruder to develop SCF/PP composite granules. The composite granules were extruded in a single screw extruder and then wound to develop SCF/PP filaments. SCF/PP filaments were produced with varying content of SCF ranging from 4 to 22 wt%. The developed composite filaments were injected by a 3D printer to produce testing samples. 3D printed SCF/PP composites with different SCF contents were investigated by analyzing their mechanical, physical, and morphological properties. The SCF/PP composites developed have shown great enhancement in their mechanical properties (tensile strength and impact toughness). The tensile strength of the 22%SCF/PP composite increased by 150% when compared to the neat PP, while the impact energy of the 22%SCF/PP composite was enhanced by 260% of the neat PP. However, the strain at break values decreased linearly in composites up to 11 wt% SCF content followed by a sudden drop in strain values in composite with 14 wt% SCF.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Experimental and multiscale analysis of volume fraction effects in tensile properties of recycled PLA-PDA/kenaf fiber 3D printing filament composites

Sanusi Hamat M.R. Ishak S.M. Sapuan N. Yidris M.S. Hussin S.A. Showkat Ali M. Ibrahim a Department of Aerospace Engineering,Faculty of Engineering,Universiti Putra Malaysia,Darul Ehsan,43400,Selangor,Malaysiab Faculty of Mechanical Engineering & Technology,Universiti Malaysia Perlis,Ulu Pauh,02600,Perlis,Malaysiac Aerospace Malaysia Research Centre (AMRC),Universiti Putra Malaysia,Darul Ehsan,43400,Selangor,Malaysiad Laboratory of Biocomposite Technology,Institute of Tropical Forestry and Forest Products (INTROP),Universiti Putra Malaysia,Darul Ehsan,43400,Selangor,Malaysiae Advanced Engineering Materials and Composites Research Centre (AEMC),Department of Mechanical and Manufacturing Engineering,Universiti Putra Malaysia,Darul Ehsan,43400,Selangor,Malaysiaf Department of Mechanical and Manufacturing Engineering,Universiti Putra Malaysia,Serdang,43400,Selangor,Malaysia

DOI: https://doi.org/10.1080/09243046.2024.2425468

IF: 2.92

2024-11-10

Advanced Composite Materials

Abstract:Polylactic acid, a biodegradable thermoplastic derived from renewable sources, has notable environmental advantages and versatile properties. However, recycled PLA often experiences reduced mechanical strength and altered chemical composition due to the recycling process, limiting its suitability for 3D printing filament applications. Recognizing the inherent limitations of recycled PLA (rPLA), this research employs a unique method of coating rPLA with dopamine (DA) and reinforcing it with kenaf fibers (KF) at various weight fractions, introducing a novel multiscale modeling approach to address the challenges of interfacial bonding and tensile performance in recycled polymers. The methodology integrates experimental single filament tensile testing with multiscale finite element modeling to accurately predict the composite's mechanical behavior across different scales. The findings reveal that a 5% kenaf fiber weight/volume fraction provides the optimal balance between tensile strength, stiffness, and toughness, achieving a significant 49.3% improvement over the unreinforced rPLA. However, increasing the kenaf fiber content beyond 5% leads to a decline in mechanical properties, attributed to higher fiber agglomeration and suboptimal fiber-matrix interactions. The novelty of this research lies in its combined use of PDA coating, natural kenaf fiber reinforcement, and advanced multiscale modeling to enhance and predict the performance of rPLA-PDA/kenaf composites, paving the way for sustainable, high-performance materials in 3D printing applications.

materials science, composites
Upcycling waste polypropylene with basalt fibre reinforcement enhancing additive manufacturing feedstock for advanced mechanical performance

Pouyan Ghabezi,Omid Sam-Daliri,Tomas Flanagan,Michael Walls,Noel M. Harrison

DOI: https://doi.org/10.1016/j.apmt.2024.102486

IF: 8.663

2024-10-26

Applied Materials Today

Abstract:This research seeks to overcome the printing and processing challenges of using waste polypropylene (PP) reinforced with short basalt fibres, transforming them into upcycled feedstock for additive manufacturing. It introduces an optimised method for producing filaments and 3D printing with these materials, addressing common issues such as adhesion and warpage through innovative techniques while achieving maximum mechanical performance in the resulting composites. Basalt fibre weight fractions of 0 %, 2 %, 5 %, 8 %, 15 %, 30 %, and 50 % were used to reinforce the recycled polypropylene, improving both printability and mechanical properties. The tensile strength reached 53.58 MPa at 15 % fibre content, while the flexural strength peaked at 34.06 MPa with 30 % fibre content, revealing distinct interactions between the fibres and polymer under tensile and flexural loading that were not previously observed. Microstructure, voids, debonding, and dispersion were examined using optical and scanning electron microscopy. Differential Scanning Calorimetry (DSC) was performed to assess the thermal behaviour and crystallinity of the recycled polymer during filament production and printing, revealing slight matrix degradation during these processes. The findings highlight the potential of waste basalt fibre-reinforced PP as a valuable filament feedstock for 3D printing, supporting a circular economy approach to composite manufacturing.

materials science, multidisciplinary
Towards a Circular Economy: Study of the Mechanical, Thermal, and Electrical Properties of Recycled Polypropylene and Their Composite Materials

Tongsai Jamnongkan,Nitchanan Intraramongkol,Wesarach Samoechip,Pranut Potiyaraj,Rattanaphol Mongkholrattanasit,Porntip Jamnongkan,Piyada Wongwachirakorn,Masataka Sugimoto,Hiroshi Ito,Chih-Feng Huang

DOI: https://doi.org/10.3390/polym14245482

IF: 5

2022-12-15

Polymers

Abstract:This research focuses on the mechanical properties of polypropylene (PP) blended with recycled PP (rPP) at various concentrations. The rPP can be added at up to 40 wt% into the PP matrix without significantly affecting the mechanical properties. MFI of blended PP increased with increasing rPP content. Modulus and tensile strength of PP slightly decreased with increased rPP content, while the elongation at break increased to up to 30.68% with a 40 wt% increase in rPP content. This is probably caused by the interfacial adhesion of PP and rPP during the blending process. The electrical conductivity of materials was improved by adding carbon black into the rPP matrices. It has a significant effect on the mechanical and electrical properties of the composites. Stress-strain curves of composites changed from ductile to brittle behaviors. This could be caused by the poor interfacial interaction between rPP and carbon black. FTIR spectra indicate that carbon black did not have any chemical reactions with the PP chains. The obtained composites exhibited good performance in the electrical properties tested. Finally, DSC results showed that rPP and carbon black could act as nucleating agents and thus increase the degree of crystallinity of PP.

polymer science
Thinking Green on 3D Printing: Sustainable Polymer Compositions of Post-Consumer Polypropylene and Tire Rubber Crumbs Intended for Industrial Applications

Sandra Paszkiewicz,Jacek Andrzejewski,Daniel Grochała,Kamil Adamczyk,Paweł Figiel,Elżbieta Piesowicz,Katarzyna Pokwicka-Croucher

DOI: https://doi.org/10.3390/ma17215209

IF: 3.4

2024-10-26

Materials

Abstract:Year by year, more and more plastic is used worldwide. A large part of post-consumer waste is still stored in landfills instead of being reused. The solution to this problem may be recycled materials (recyclates) or biodegradable materials. The method of 3D printing, regarded as a clean processing technology, can significantly contribute to addressing global plastic pollution by utilizing post-consumer recycled polymers to create new components and parts. Therefore, this study focuses on the assessment of various properties and characteristics of 3D-printed compositions based on post-consumer polypropylene (PP) and rubber crumbs, recycled from packages foils and car tires, respectively. Moreover, within this study, we compared the mechanical performance of the injection molding material with the one obtained from 3D printing. A characterization was made considering the thermal and mechanical properties as well as the "print quality" through the microscopic and tomographic analysis of subsequent print passes, the number of free spaces, and imperfections in the polymer melt. Samples obtained using the FDM and injection methods exhibited comparable melting temperatures, while the samples obtained by injection molding exhibited slightly better mechanical performance, higher hardness, and impact strength.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Modification of chain extension and crosslinking structures of recycled polyester textile for 3D printing filament

Lingquan Hu,Jianzhong Sun,Meng Zhang,Jun Liu,Shouxiang Jiang

DOI: https://doi.org/10.1002/vnl.22176

2024-11-06

Journal of Vinyl and Additive Technology

Abstract:ADR4468 modification of recycled polyesters assembling core‐shell structures. The increase in amount of polyester textile waste is contributing to the severity of environmental pollution because polyester cannot be easily recycled. To reduce the limits of its recyclability, a value‐added recycling approach should be explored. This work introduces an approach for recycling polyester textiles into 3D printable filaments. To increase recyclability of polyester textiles, the polyester materials are modified by ADR4468 additive. After the polyester is 3D printed, the sample with 1.0 wt% of ADR4468 shows the highest tensile and compressive strength properties compared with 1.5 and 2.0 wt%, owing to its fewer voids between the printed lines, a fish scale‐like morphology that spreads out, and a higher degree of crystallization. Moreover, the mechanism of modification suggests that ADR4468 extends and crosslinks the polyester chains by ring‐opening reactions of epoxy groups of ADR4468 and forms sea‐island structures. The sea‐island structures of bonded polyester branched cores with tangled polyester shell interface areas and unbonded polyester chain areas performed suitable rheological behaviors to recycle polyester textiles for 3D printable filaments production. The filaments can be used to replace commercially available filaments, offer a sustainable option for consumers, and impact both the polyester textile‐related recycling and 3D printing industries. Highlights An approach is proposed to recycle polyester textiles for 3D printing filament The approach uses a mechanical method to recycle polyester textiles Recycled polyesters were modified by ADR4468 to form core‐shell structures Core‐shell structures were separated by short polyesters(sea‐island structure) The structures met rheological behaviors for 3D printing filament

chemistry, applied,materials science, textiles,polymer science
Material property characterization of 3D printed polypropylene wood plastic composites

Sungjun Hwang,Gavin Fowler,Yousoo Han,Douglas J. Gardner

DOI: https://doi.org/10.1002/pc.28890

IF: 5.2

2024-08-10

Polymer Composites

Abstract:3D printed hexagons and specimens of polypropylene wood plastic composites. Wood flour (WF) at 10 wt.% and 20 wt.% loadings was used as a reinforcing filler to enhance the applicability of polypropylene (PP) for 3D printing. After performing printability tests of PP wood plastic composites (WPCs), the mechanical properties of both injection‐molded and 3D‐printed PP WPC specimens were explored. Test specimens were prepared from 3D printed hexagons for analyzing the mechanical properties. Adding WF to neat PP increased the storage modulus and the glass transition temperature while decreasing the degree of crystallinity and the coefficient of thermal expansion, while enhancing the printability of neat PP. The tensile strength, tensile modulus of elasticity, flexural strength, and flexural modulus of elasticity of injection‐molded neat PP improved by up to 21%, 59%, 30%, and 56%, respectively, with 20 wt.% WF. However, the impact strength of injection‐molded neat PP decreased by 85%, with 20 wt.% WF. After 3D printing, the tensile strength and tensile modulus of elasticity of printed neat PP increased by up to 84% and 60%, respectively, with 20 wt.% WF. The flexural strength and flexural modulus of elasticity of neat printed PP remained unchanged compared to those of PP filled with 20 wt.% WF, while the impact strength decreased by 87%. Highlights WF was used as a reinforcement in polypropylene designed for 3D printing A pilot‐scale, pellet‐fed 3D printer was used to print hollow hexagons, and then test specimens were fabricated from these hexagons for mechanical properties The tensile and flexural properties of 3D printed neat polypropylene improved, while the impact strength decreased after adding 20 wt.% WF to the neat PP.

materials science, composites,polymer science

The Tensile Properties of Recycled Polypropylene Filament (rPP) as 3D Printing Material

Glass Powder Additive on Recycled Polypropylene Filaments: A Sustainable Material in 3D Printing

The Mechanical and Physical Properties of 3D Printing Filament made from Recycled Polypropylene and Ground Tyre Rubber Treated with Alkali

Material Characterizations of the Polymers Reinforced with Recycled Flexible Plastic Blends as Filament for 3D Printing

Recycled polypropylene blends as novel 3D printing materials

Development and Characterization of Rice Husk and Recycled Polypropylene Composite Filaments for 3D Printing

Short basalt fibre reinforced recycled polypropylene filaments for 3D printing

Optimization of Glass-Powder-Reinforced Recycled High-Density Polyethylene (rHDPE) Filament for Additive Manufacturing: Transforming Bottle Caps into Sound-Absorbing Material

The Properties of Glass Fiber Reinforced Polypropylene Filaments Recycled from Fishing Gear

Development and characterization of sustainable 3D printing filaments using post-consumer recycled PET: processing and characterization

Recycling polypropylene from non-woven disposable masks in developing a three-dimensional printing filament

3D printing of polypropylene using the fused filament fabrication technique

Designing 3D printable polypropylene: Material and process optimisation through rheology

Development of 3D printing short carbon fiber reinforced polypropylene composite filaments

Experimental and multiscale analysis of volume fraction effects in tensile properties of recycled PLA-PDA/kenaf fiber 3D printing filament composites

Upcycling waste polypropylene with basalt fibre reinforcement enhancing additive manufacturing feedstock for advanced mechanical performance

Towards a Circular Economy: Study of the Mechanical, Thermal, and Electrical Properties of Recycled Polypropylene and Their Composite Materials

Thinking Green on 3D Printing: Sustainable Polymer Compositions of Post-Consumer Polypropylene and Tire Rubber Crumbs Intended for Industrial Applications

Modification of chain extension and crosslinking structures of recycled polyester textile for 3D printing filament

Material property characterization of 3D printed polypropylene wood plastic composites