Abstract:The paper substantiates the composition and prospects of using high strength Al–Zn–Mg–Ca–Fe casting aluminum alloy without heat treatment based on the study on the structure, technological and mechanical properties. Alloys of the base composition Al–5.5%Zn–1.5%Mg (wt.%) jointly and separately doped with 0.5–1.0 % Ca and 0.5 % Fe were obtained as the objects of research. Standard casting alloys according to GOST 1583-93: AK12M2, AMg6lch, AM4,5Kd were the objects of comparison. A hot tensile test using a cast test bar was conducted to check the tendency to form hot cracks due to hindered contraction. It was shown that separate alloying with calcium and iron does not contribute to the improvement of crack resistance and adversely affects mechanical properties. Combined alloying with 1 % Ca and 0.5 % Fe improves the hot tearing resistance to the level of the AMg6lch alloy properties. This effect is due to calcium-containing phases of eutectic origin formed and a favorable grain structure created that is free from columnar grains. Iron in the alloy structure is bound in compact Al 10 CaFe 2 phase particles as a result of the non-equilibrium crystallization during permanent mold casting. The formation of this phase allowed to reduce the amount of zinc in the (Al, Zn) 4 Ca phase and mostly retain the (Al) solid solution composition as evidenced by similar hardness values of the Al–5.5%Zn–1.5%Mg base alloy and Al–5.5%Zn–1.5%Mg–1%Ca–0.5%Fe alloy, and the superiority of the values over the hardness of alloys separately alloyed with calcium and iron. Also the cast hardness of the promising alloy more than 20 HV higher than the cast hardness of commercial cast alloys. The new alloy in the as-cast condition exhibited competitive mechanical tensile properties: UTS ~ 310 MPa, YS ~ 210 MPa, El ~ 4 %.

MHD-processes and equipment for continuous casting of aluminum alloy ingots

The Stand of Horizontal Continuous Casting of Al and its Alloys

Development of the manufacturing process of aluminum alloys with high strength and conductance

Research On Alloying Tecniques Of Mischmetal In Die Casting Magnesium Alloy

Production of Al-Zr Master Alloy by Electrolysis of the KF-NaF-AlF3-ZrO2 Melt: Modifying Ability of the Master Alloy

MELT CONDITIONED HIGH PRESSURE DIE CASTING (MC-HPDC) OF Mg-ALLOYS

Study on Grain Refinement and Homogenization of Large-Sized DC Casting Ingot by A-EMS Melt Treatment

Relationship of Compositions, Phase Constituents and Solidification Paths of Casting Mg-Al-Zn Alloys

New high-strength casting aluminum alloy based on the Al–Zn–Mg–Ca–Fe system without requirement for heat treatment

Effect of combining continuous casting and simultaneous solidliquid metal deformation on the structure and properties of alloy V95 products

Melt-Conditioned, High-Pressure Die Casting of Mg–Zn–Y Alloy

Research on Magnetic Floating Horizontal Continuous Casting Process (MFCC) for Nearly Net-Shape Molten Metal Afterheat Billet

Melt Conditioned Direct Chill Casting (MC-DC) Process for Production of High Quality Aluminium Alloy Billets

Deformation mechanisms and mechanical properties of the high-strength and ductile Al-Zn-Mg-Cu alloys processed by repetitive continuous extrusion forming process with different heat treatments

A high strength Al-Zr alloy with good electrical conductivity by combining gas-assisted continuous casting and extrusion with subsequent thermomechanical treatment

Research Status of High-Manganese High-Aluminum Steel and Key Points of Continuous Casting

Research progress on semi-continuous casting of magnesium alloys under external field

The simultaneous application of variable frequency ultrasonic and low frequency electromagnetic fields in semi continuous casting of AZ80 magnesium alloy

Microstructures and Macrosegregation of Al–Zn–Mg–Cu Alloy Billet Prepared by Uniform Direct Chill Casting

A Continuous Casting Device with Electromagnetic Stirring for Production of SSM Feedstock Using Al-Si Alloys

Use of rapid solidification in processing of aluminum alloys with reduced deep-sea nodules