Abstract:Lithium metal anode should satisfy significant requirements related to fast‐charging feasibility and high‐energy‐density battery design. The hyperporous/hybrid conductive electrode induces simultaneous lithium deposition and facile lithium densification kinetics at fast current density. Besides, carbon‐based ultra‐light architecture realizes dramatic weight reduction of lithium metal anode, compared with a typical metal current collector to effectively achieve high gravimetric energy density. Lithium metal anode (LMA) emerges as a promising candidate for lithium (Li)‐based battery chemistries with high‐energy‐density. However, inhomogeneous charge distribution from the unbalanced ion/electron transport causes dendritic Li deposition, leading to "dead Li" and parasitic reactions, particularly at high Li utilization ratios (low negative/positive ratios in full cells). Herein, an innovative LMA structural model deploying a hyperporous/hybrid conductive architecture is proposed on single‐walled carbon nanotube film (HCA/C), fabricated through a nonsolvent induced phase separation process. This design integrates ionic polymers with conductive carbon, offering a substantial improvement over traditional metal current collectors by reducing the weight of LMA and enabling high‐energy‐density batteries. The HCA/C promotes uniform lithium deposition even under rapid charging (up to 5 mA cm−2) owing to its efficient mixed ion/electron conduction pathways. Thus, the HCA/C demonstrates stable cycling for 200 cycles with a low negative/positive ratio of 1.0 when paired with a LiNi0.8Co0.1Mn0.1O2 cathode (areal capacity of 5.0 mAh cm−2). Furthermore, a stacked pouch‐type full cell using HCA/C realizes a high energy density of 344 Wh kg−1cell/951 Wh L−1cell based on the total mass of the cell, exceeding previously reported pouch‐type full cells. This work paves the way for LMA development in high‐energy‐density Li metal batteries.

Redox-homogeneous, gel electrolyte-embedded high-mass-loading cathodes for high-energy lithium metal batteries

An Ultrastable Lithium Metal Anode Enabled by Designed Metal Fluoride Spansules

A medium-entropy transition metal oxide cathode for high-capacity lithium metal batteries

Non-flammable electrolyte enables Li-metal batteries with aggressive cathode chemistries

Synergistic Dual‐Additive Electrolyte Enables Practical Lithium‐Metal Batteries

Gel Electrolyte Modification Enables Planar Li Deposition and Fast Kinetics Toward High Energy Li Metal Batteries

Conductive gel composite cathodes with high mass loading of active oxides for high-performance solid-state lithium metal batteries

A High‐Performance Lithium Metal Battery with Ion‐Selective Nanofluidic Transport in a Conjugated Microporous Polymer Protective Layer

500 Wh kg −1 Class Li Metal Battery Enabled by a Self‐Organized Core–Shell Composite Anode

A mismatch electrical conductivity skeleton enables dendrite–free and high stability lithium metal anode

Dual-anion ionic liquid electrolyte enables stable Ni-rich cathodes in lithium-metal batteries

Stable Li Metal Anode with Protected Interface for High-Performance Li Metal Batteries

Stabilized Li metal anode with robust C-Li3N interphase for high energy density batteries

Facile Lithium Densification Kinetics by Hyperporous/Hybrid Conductor for High‐Energy‐Density Lithium Metal Batteries

Enhancing Lithium-Ion Diffusion Kinetics in a 3D Lithium Metal Host through Surface Modification with Hierarchical Multimetal Oxides

Nonporous Gel Electrolytes Enable Long Cycling at High Current Density for Lithium-Metal Anodes.

(Invited) Designing New Electrolytes for High-Energy Lithium Metal Batteries

Stable Lithium Metal Anode Enabled by a Lithiophilic and Electron/Ion Conductive Framework

Interconnected Hollow Carbon Nanospheres for Stable Lithium Metal Anodes.

High-voltage lithium-metal battery with three-dimensional mesoporous carbon anode host and ether/carbonate binary electrolyte

Electrical Conductivity Gradient Based on Heterofibrous Scaffolds for Stable Lithium‐Metal Batteries