Abstract:Conventional thixoforming technology had advantages of casting and forging, but low plastic deformation degree and existence of liquid phase lowered the mechanical property. In this work, 6A02 bracket-shape component was firstly manufactured by the efficient thixoforming-forging compound forming technology and bimodal semisolid billet. Bimodal semisolid feedstock was beneficial for both filling ability and mechanical strength due to intragranular dislocation and elongated grain shape. Firstly, a Deform-3D simulation of compound forming was established by controlling temperature field distribution. Then the effects of billet shapes, billet temperatures, soaking times, mold temperatures and dwell times on microstructures and mechanical properties were investigated. Though the mechanical strength and ductility at the shoulder were elevated by larger plastic deformation in the integrated forming process, they were still lower than those at side wall and bottom part in virtue of liquid segregation. Besides, the largest yield strength σ y , tensile strength σ max and elongation δ of compound-formed 6A02 components were even 16.8%, 25.8%, and 77.6% higher than σ y , σ max and δ of 6A02 hot-extruded bar, respectively. Finally, the deformation behavior and strengthening mechanism of compound forming technology were discussed deeply. Particularly, except liquid fraction, deformation behavior was relevant with grain size and morphology. For rounder and smaller grains, grain boundary sliding was dominant. But slip deformation was predominant for large-deformed grains. Subsequently, a new dynamic recrystallization (DRX) mechanism was proposed and only continuous dynamic recrystallization (CDRX) could make the wet grain boundary serrated. A quantitative insight into strengthening mechanism indicated that solid solution strengthening and dislocation strengthening were dominant. This study provided a theoretical guidance and experimental support for the efficient application and forming control of 6A02 alloy in compound forming area.

Innovation for forming aluminum alloy thin shells at ultra-low temperature by the dual enhancement effect

Wrinkling and Strengthening Behaviors in the Two-Layer-Sheet Hot-Forming–Quenching Integrated Process for an Al–Cu–Mg-Alloy Thin-Walled Curved-Surface Shell

Investigation on the formability and deformation mechanism of aluminum alloy thin-walled parts at cryogenic temperature

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

Application of Combined W-Temper and Cold Forming Technology to High-Strength Aluminum Alloy Automotive Parts

Characteristics of 2D Ultrasonic Vibration Incremental Forming of a 1060 Aluminum Alloy Sheet

Developments and perspectives on the precision forming processes for ultra-large size integrated components

Comparative study on the formability and microstructure evolution of different tempered Al–Cu–Li alloy sheets during room and cryogenic temperature forming process

Development of High Performance of Al Alloys via Cryo‐Forming: A Review

Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet

Strength and Formability Improvement of Al-Cu-Mn Aluminum Alloy Complex Parts by Thermomechanical Treatment with Sheet Hydroforming

High-efficiency forming processes for complex thin-walled titanium alloys components: state-of-the-art and perspectives

Thixoforming-forging compound forming technology for 6A02 Al bracket-shape component

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

Cold forging of high strength aluminum alloys and the development of new thermomechanical processing

Study on warm forming process of rigid-flexible composite drawing based on numerical simulation

Experimental and Numerical Study of Forming Limit in 1060 Aluminum Ultrasonic Vibration Single Point Incremental Forming

Investigation of Microstructures and Mechanical Properties of Ultra-High Strength Al-Zn-Mg-Cu Alloy Prepared by Rapid Solidification and Hot Extrusion

Approaching theoretical strength in aluminum alloys via directional heterogeneous nanostructured design

Influence of cryogenic–vibration compound field on the residual stress and forming accuracy during aluminum alloy forming

Advances in Microstructure Control during Isothermal Forming of Ti-Alloy Large Complex Components by Near-β Local Forging