Abstract:The Heusler-type Fe2VAl alloy is a promising candidate for use in fabricating a thermoelectric power generation device because of its large Seebeck coefficient and high electrical conductivity. However, the high thermal conductivity of this alloy, as a thermoelectric material, degrades its power generation capacity. In this study, to reduce its thermal conductivity, the microstructure of a sintered Fe2V1.08Al0.92 alloy prepared via a powder metallurgical process was modified by adding oxide nanoparticles. Via the dispersion of Al2O3 nanoparticles, a sintered Fe2V1.08Al0.92 alloy with fine grains of approximately 200 nm in size was obtained due to the pinning effect on grain growth during sintering. The thermal conductivity was reduced from 16 to 11 W/mK. Upon La2O3 addition, the grain size of the Fe2V1.08Al0.92 alloy was reduced to approximately 100 nm and the thermal conductivity was further reduced to 10 W/mK. The difference in grain refinement could be caused by the lower stability of La2O3, which facilitated dispersion during ball milling, compared to that of Al2O3. As these microstructure refinements negatively affected the electronic properties, the thermoelectric performance of the Fe2V1.08Al0.92 alloy could not be enhanced. However, partial microstructure refinement with sparsely distributed La2O3 could slightly enhance the thermoelectric performance due to an appreciable reduction in the thermal conductivity without a considerable degradation in the electronic properties. By using these thermoelectric properties, a simple estimation of thermoelectric power generation, assuming a thermal resistance between the heat sources and thermoelectric module, was conducted. Remarkably, the results suggested that the reduction in thermal conductivity could enhance the output power density and conversion efficiency and reduce the optimal leg length. Thus, practically, controlling the balance between the electronic and thermal properties via microstructural modification is favorable in improving the practicability of the Fe2VAl alloy by enhancing the power generation capacity and reducing the sizes and masses of thermoelectric devices.

Co-Cr-Fe-Mn-Ni Oxide as a Highly Efficient Thermoelectric High-Entropy Alloy

A novel valence-balanced double half-Heusler Ti2Zr2Hf2NbVFe5Ni3Sb8 alloy by high entropy engineering

Tailoring Ni/Fe Doping for Superior Thermoelectric Performance of Zr2Ni2−xFexSnSb (x = 0.30, 0.35, 0.40) High‐Entropy Alloys

Microstructure of a spark-plasma-sintered Fe2VAl-type Heusler alloy for thermoelectric application

A novel and sustainable method to develop non-equiatomic CoCrFeNiMox high entropy alloys via spark plasma sintering using commercial commodity powders and evaluation of its mechanical behaviour

High-Performance Thermoelectric Oxides Based on Spinel Structure

Investigation of PbSnTeSe High-Entropy Thermoelectric Alloy: A DFT Approach

Entropy Engineering of SnTe: Multi‐Principal‐Element Alloying Leading to Ultralow Lattice Thermal Conductivity and State‐of‐the‐Art Thermoelectric Performance

Fast fabrication of SnTe via a non-equilibrium method and enhanced thermoelectric properties by medium-entropy engineering

High thermoelectric performance in metallic NiAu alloys

Magnetocaloric properties of melt-spun MnFe-rich high-entropy alloy

Thermoelectric Transport of a Novel Zr‐Based Half‐Heusler High‐Entropy Alloy

Curie Temperature Engineering in High Entropy Alloys for Magnetocaloric Applications

High symmetry structure and large strain field fluctuation lead enhancement of thermoelectric performance of quaternary alloys by tuning configurational entropy

Microstructures and Thermoelectric Properties of Heusler Fe 2 VAl Alloys Containing Oxide Nanoparticles

High-entropy-stabilized chalcogenides with high thermoelectric performance

221 Fabrication and Performance Improvement of CuAlO_2 Thermoelectrics by Orientation Process and Densification

Adaptable sublattice stabilized high-entropy materials with superior thermoelectric performance

Comparison between the thermoelectric properties of new materials: The alloy of iron, vanadium, tungsten, and aluminum (Fe2V0.8W0.2Al) against an oxide such as NaCO2O4

Effect of annealing on mechanical and thermoelectric properties of a Al2CoCrFeNi high-entropy alloy

Entropy-Assisted High-Entropy Oxide with a Spinel Structure toward High-Temperature Infrared Radiation Materials