Abstract:Thermochemical conversion of biomass has been studied extensively over the last decades. For the design, optimization and modeling of thermochemical conversion processes, such as fixed bed pyrolysis, a sound understanding of pyrolysis is essential. However, the decomposition mechanism of most biomass types into gaseous, liquid, and solid fractions is still unknown because of the complexity of pyrolysis and differences in biomass composition.The aim of this study was to find characteristic differences in the pyrolysis behavior of three widely used biomass feedstocks to optimize the performance of industrial fixed bed pyrolysis. This aim was achieved in three steps. First, devolatilization kinetics during pyrolysis of three biomass types was investigated in a thermogravimetric analyzer (TGA). Then, a one-step multi-component pyrolysis model with three independent parallel reactions for hemicellulose, cellulose and lignin was derived to correlate the kinetics with single component decomposition and to identify their amount in the biomass sample. In a final step, the findings were tested in a fixed bed reactor at laboratory scale to prove applicability in industrial processes.Three types of biomass were chosen for this investigation: wheat straw, rape straw and spruce wood with bark. They represent biomass with a high cellulose, hemicellulose and lignin content, respectively. Since lignin is the most stable and complex of these three biomass components, its amount is assumed to be the main controlling factor in the thermochemical decomposition process.The thermogravimetric (TG) curve of spruce wood with bark was found to shift to about 20K higher temperatures compared to the TG curves of straw and rape straw. This result indicates that a higher activation energy is needed to decompose woody biomass, which contains a higher amount and a different type of lignin than straw. Three wood decomposition phases were distinguished from the negative first derivatives curves (DTG): a shoulder during hemicellulose decomposition, a peak during cellulose decomposition and a smaller rise during lignin decomposition. By comparison both herbaceous biomass types decomposed in only two phases at lower temperatures. The decomposition of the herbaceous, and woody biomass samples was completed at about 830K and 900K, respectively, leaving only a solid residue of ash. The derived pyrolysis model estimated the composition and described the devolatilization curves of each biomass with sufficient accuracy for industrial processes, although the same activation energy set, taken from the literature, was used for each biomass. In the fixed bed pyrolysis experiments similar characteristics were found to those in the TGA experiments. Herbaceous biomass with a higher cellulose and hemicellulose content decomposed faster and produced a larger fraction of gaseous products than woody biomass with a higher lignin content. According to the assessment of the product distribution, performed after each experiment, woody biomass pyrolysis led to a larger fraction of solid products than herbaceous biomass pyrolysis. We conclude that industrial fixed bed pyrolysis can be optimized for different biomass feedstocks with a specific composition of cellulose, hemicellulose and lignin.

Towards the Production of High Added-Value Products from the Pyrolysis and Steam Pyro-Gasification of Five Biomass-Based Building Insulation Materials at End-of-Life

Potential of products from high-temperature pyrolysis of biomass and refuse-derived fuel pellets

Activated waste cotton cellulose as renewable fuel and value-added chemicals: Thermokinetic analysis, coupled pyrolysis with gas chromatography and mass spectrometry

Valorisation of biomass pellets to renewable fuel and chemicals using pyrolysis: characterisation of pyrolysis products and its application

Pyrolysis-catalytic upgrading of bio-oil and pyrolysis-catalytic steam reforming of biogas: a review

Estimation of the heat required for intermediate pyrolysis of biomass

A Comparative Analysis of Waste Biomass Pyrolysis in Py-GC-MS and Fixed-Bed Reactors

Thermal Properties of Biochars Derived from Waste Biomass Generated by Agricultural and Forestry Sectors

The effect of the biomass components lignin, cellulose and hemicellulose on TGA and fixed bed pyrolysis

Comparative study on pyrolysis and catalytic pyrolysis upgrading of biomass model compounds: thermochemical behaviors, kinetics, and aromatic hydrocarbon formation

Materials, fuels, upgrading, economy, and life cycle assessment of the pyrolysis of algal and lignocellulosic biomass: a review

Biomass Pyrolytic Polygeneration System: Adaptability for Different Feedstocks

Pyrolysis of Specific Non-Recyclable Waste Materials: Energy Recovery and Detailed Product Characteristics

Pyrolysis of wastewater sludge and composted organic fines from municipal solid waste: laboratory reactor characterisation and product distribution

Green Catalytic Pyrolysis: An Eco-Friendly Route for the Production of Fuels and Chemicals by Blending Oil Industry Wastes and Waste Furniture Wood

Cellulose, hemicellulose and lignin slow steam pyrolysis: Thermal decomposition of biomass components mixtures

Pyrolysis of municipal solid waste compost: Pilot plant evaluation as a sustainable practise of waste management

Thermal analysis technology to utilize waste biomass and waste heat to produce high-quality combustible gas through simulations and experiments

Upgradation of agricultural straw pyrolysis through co-processing with PE waste and by-product detoxification

Valorization of Hemp Stalk Waste Through Thermochemical Conversion for Energy and Electrical Applications

Challenges and Perspectives of the Conversion of Lignin Waste to High-Value Chemicals by Pyrolysis