Abstract:The current industrial development has entered the industrial era 4.0 marked by progress from various aspects, for example the development of microcontroller-based controller technology to be applied to smarthomes. One of them is controlling and monitoring dangerous air pollution and if it is inhaled directly by humans in large enough quantities it will cause health problems in respiratory function. There are various kinds of air pollution, such as CO and CO2 which are found in burning cigarettes or other burning which is carried out every day in households. In addition to hazardous substances, to support a complete smarthome-based research, it is also necessary to add a sensor to detect fires and gas leaks in households. This study aims to design and manufacture a room pollution detector using the MQ-2, MQ-6 and Flame Sensor sensors to detect air pollution caused by CO and CO2 and detect LPG gas leaks and detect fires with notifications via led matrix and based alarms. arduino . The results of this study indicate that to design and manufacture pollution detectors using a smoke sensor that uses Arduino Uno as a microcontroller that controls the work of the system connected to the MQ-2 sensor used to detect smoke, the MQ-6 sensor to detect LPG gas, and to detect fire use Flame. Sensor (Fire Sensor) DFR0076. From the results obtained by the MQ2 smoke sensor, the resistance value of the sensor will decrease when smoke is given, otherwise the sensor resistance value will increase when smoke is not given. The sensor resistance ranges from 150 Ω – 300 Ω when smoked and 1.5 KΩ to 1.7 KΩ when not smoked. gas sensor resistance increases when given gas and decreases when it does not detect gas. The sensor resistance when reading the presence of gas in the air is between 100 Ω - 400 Ω, and when it does not detect gas, it is 0 Ω - 12 Ω. On the Flame sensor, the sensor voltage value changes when it detects fire. The voltage value increases if it detects fire and vice versa the sensor voltage decreases when it does not detect fire. The sensor voltage value when detecting fire is between 1.2 Volts – 5 Volts, while when it does not detect fire, it is between 0 Volts – 0.9 Volts.

PROTOTIPE SISTEM PENDETEKSI POLUSI UDARA MENGGUNAKAN SENSOR ASAP MQ-2, SENSOR GAS MQ-6 DAN SENSOR API PADA RUANGAN DENGAN OUTPUT ALARM BERBASIS MIKROKONTROLLER ARDUINO

Prototype Alat Pendeteksi Kebakaran Menggunakan Sensor Flame dan MQ-2 Berbasis Arduino Uno

SMOKE DETECTION DESIGN USING MQ-2 SENSOR AND EXHAUST FAN BASED ON MICROCONTROLLER

Alarm Pengendali Asap Pada Ruangan Bebas Asap Berbasis Mikrokontroler Arduino

Prototype Design of CO2, CH4 and SO2 Toxic Gas Detectors in the Room Using Microcontroller-Based Fuzzy Logic

Design of Smoke Detector for Smart Room Based on Arduino Uno

Design of Multi-gas Monitoring Device for Indoor Air Quality

PERANCANGAN SISTEM KEAMANAN RUMAH BERBASIS IoT DENGAN NodeMCU ESP8266 MENGGUNAKAN SENSOR PIR HC-SR501 DAN SENSOR SMOKE DETECTOR

Simple and Cost-Effective Detection of Carbon Monoxide Gas

Air Quality Detection and Notification using Arduino IDE

Design of Arduino-based LPG Gas Leak Detection Tool using MQ-6 Sensor

Implementasi Sensor MQ2 Sebagai Pendeteksi Kebocoran Gas Pada Fire Alarm Dengan Android

Perancangan Alat Pendeteksi Kebocoran Tabung Gas ELPIJI Berbasis Arduino Uno

Monitoring dan Kontrol Gas CO Dalam Ruangan Berbasis Pemrograman LabVIEW dan Mikrokontroler

Fire And Smoke Detector Alarm Using Arduino And MQ2 Sensor

Microcontroller-based air quality monitoring design using mamdani fuzzy method

Implementation of An Application-Based Motor Vehicle Exhaust Emission Level Detection System

Sistem Deteksi Dini dan Pemadaman Kebakaran Otomatis di Rumah Berbasis IoT Menggunakan NodeMCU ESP32

RANCANG BANGUN ALAT PENDETEKSI DINI PONTENSI KEBAKARAN SECARA OTOMATIS pada RUANGAN TERINTGRASI dengan INTERNET of THINGS

CO2 detection system in mixed gas using MQ-135 sensor

Design of a Prototype of Smoke Exhaust Control System in an Enclosed Room with the Fuzzy Sugeno Method