Abstract:In spite of the advantages of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathode materials such as high energy density and high capacity, their capacity decay during cycling is still a significant problem, which are mainly due to the internal structural collapse and the surge in interfacial impedance caused by interfacial side reactions. To address these issues, wet chemical methods and annealing treatments were used to create LiV 2 O 4 -coated and V 4+ -doped NCM811 cathode materials. The LiV 2 O 4 coating layer and the doped V 4+ had little effect on the crystal structure of the NCM811, according to X-ray powder diffraction and Rietveld refinement studies. Scanning electron microscopy, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy data all showed that the LiV 2 O 4 layer was successfully coated on the surface of the spherical particles and some of the V 4+ was successfully introduced into the bulk phase. Thanks to the ion-conducting layer, LiV 2 O 4 , the interfacial impedance was reduced while the Li + diffusion rate was accelerated, and the V 4+ doped into the bulk phase stabilizes the internal structure, significantly increasing the cycling stability and the rate performance of NCM811. In particular, when the coating amount was 0.6 wt%, the initial discharge specific capacity reached 203.5 mAh/g at 2.8–4.3 V at 0.1 C, and the retention rate was 87.6% after 100 cycles, which was 12.1% higher compared to 75.5% of the original sample. And when the rate was raised to 5 C, the original sample's capacity plummeted to only about 100 mAh/g, but the sample with 0.6 wt% of coating was still 140.9 mAh/g. Experiments confirmed that this LiV 2 O 4 coating modification with synergistic V 4+ doping provided an innovative technique for boosting the electrochemical performance of Ni-rich ternary cathode materials.

Stabilization of high-voltage layered oxide cathode by utilizing residual lithium to form NASICON-type nanoscale functional coating

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

In situ epitaxial growth and electrochemical conversion of LiNi0.5Mn1.5O4 thin layer on Ni-rich cathode materials for high voltage lithium-ion batteries

Functional Passivation Interface of LiNi 0.8 Co 0.1 Mn 0.1 O 2 toward Superior Lithium Storage

Stabilization of NCM811 cathode for Li-ion batteries by N-doped carbon coating

Lithium-conductive LiNbO3 Coated High-Voltage LiNi0.5Co0.2Mn0.3O2 Cathode with Enhanced Rate and Cyclability

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

Stabilizing the Interphase in an Ultra-High-Nickel Cathode Enabling High-Performance Lithium-Ion Batteries

Sodium doping derived electromagnetic center of lithium layered oxide cathode materials with enhanced lithium storage

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Enhancing high-voltage structural stability of single-crystalline Ni-rich LiNi0.9Mn0.05Co0.05O2 cathode material by ultrathin Li-rich oxide layer for lithium-ion batteries

Improved high-voltage performance of LiNi0.87Co0.1Al0.03O2 by Li+-conductor coating

High structure stability and Li-conduction of LiNi0.8Co0.1Mn0.1O2 cathode co-coated by Al2O3 and LiNbO3 for high performance lithium-ion battery

Mitigating interfacial instability of high-voltage sodium layered oxide cathodes with coordinative polymeric structure

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Profiting the Co-Modifications of Li 2 SnO 3 Coating and Sn 4+ Doping in Co-Free Ni-Rich Cathode Particles for Lithium-Ion Batteries

Conversion of residual lithium into fast lithium ion conductor coating to achieve high cycle life LiNi0.8Co0.15Al0.05O2 cathode for lithium ion battery

Integrated co-modification of PO43− polyanion doping and Li2TiO3 coating for Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode material of Lithium-Ion batteries

Toward a High-Voltage Practical Lithium Ion Batteries with Ultraconformal Interphases and Enhanced Battery Safety

Stabilizing reaction interface in Ni-rich layered oxides cathode for high-performance lithium-ion batteries at a high cutoff voltage

Sol/Antisolvent Coating for High Initial Coulombic Efficiency and Ultra-stable Mechanical Integrity of Ni-Rich Cathode Materials