Abstract:Siliceous mesostructured cellular foams (MCF) impregnated with polyethylenimine (PEI) of various molecular weights and structures were evaluated as CO2 adsorbents. The MCF solid support consisted of a well-defined interconnected three-dimensional mesoporous structure with large cell diameter of 30.3 nm and large window diameter of 11.3 nm, filled with polyethylenimine up to 70 weight percent or about 22.3% nitrogen atom by weight of the adsorbents. While other mesoporous solid supports lost their porosity after PEI impregnation, our MCF solid support maintained its pore volume over the range of 1.12 to 1.64 cm(3) g(-1). The importance of the porosity of PEI-impregnated MCF adsorbents for high capacity CO2 adsorbents was demonstrated. The highest CO2 sorption capacity (180.6 mg-CO2/g-adsorbent or 393.6 mg-CO2/g-PEI at 75 degrees C) was obtained for silica supports loaded with 50 weight percent branched PEI with average molecular weight of 600 g mol(-1). Under dry atmospheric CO2 gas, this adsorbent reached the theoretical CO2 capacity of 0.50 mole-CO2 per mole-nitrogen within less than about 8 min, making this adsorbent one of the most effective CO2 adsorbents reported. Repeated multiple sorption cycles demonstrated good stability of this adsorbent for CO2 capture. The initial sorption kinetics determined the overall CO2 sorption capacity, which was limited by the formation of a carbamate layer as a result of the CO2-PEI complexation that due to inhibition of CO2 diffusion; the kinetics of "ionic" gelation of the impregnated PEI by CO2 controlled the overall performance of the CO2 adsorbents. At 75 degrees C, the operating temperature favored the molecular mobility of PEI and unrestricted diffusion of CO2 to allow the theoretical CO2 capacity of the PEI to be attained. Lower temperatures limited the mobilities of PEI and CO2 and the kinetics of "ionic" gel formation dominated, causing a lowered overall performance of the CO2 adsorbents. Overall, this study points to the importance of interconnected porous channel networks to optimize the performance of PEI-impregnated mesoporous silica particles.

Carboxy-functionalized polyimide aerogel monoliths: synthesis, characterization and carbon dioxide adsorption

Constructing Polyimide Aerogels with Carboxyl for CO2 Adsorption

Low cross‐linked polyimide aerogel with imidazole for CO2 adsorption

Polyethylenimine-Grafted Hkust-Type Mof/Poiyhipe Porous Composites (Pei@Pgd-H) As Highly Efficient Co(2 )Adsorbents

Preparation and Characterization of Polyimide Aerogels with a Uniform Nanoporous Framework

Directional porous polyimide/polyethylene glycol composite aerogel with enhanced CO2 uptake performance

Design of carbonized unidirectional polyimide aerogel for CO 2 capture: Effect of pore morphology/topology on CO 2 capture

Co-polyimide Aerogel Using Aromatic Monomers and Aliphatic Monomers As Mixing Diamines

Structurally Designed Synthesis of Mechanically Stable Poly(benzoxazine-co-resol)-Based Porous Carbon Monoliths and Their Application As High-Performance CO2 Capture Sorbents

Fabrication and Properties of Polyimide/Carbon Fiber Aerogel and the Derivative Carbon Aerogel

Mechanically strong and tough polyimide aerogels cross-linked with amine functionalized carbon nanotubes synthesized by fluorine displacement reaction

Porous carbon frameworks with high CO2 capture capacity derived from hierarchical polyimide/zeolitic imidazolate frameworks composite aerogels

Monolithic carbon aerogels within foam framework for high-temperature thermal insulation and organics absorption

Preparation and properties of cellulosenanofiber (CNF) /polyvinyl alcohol (PVA) /graphene oxide (GO): Application of CO2 absorption capacity and molecular dynamics simulation

Polyethylenimine-Impregnated Siliceous Mesocellular Foam Particles As High Capacity Co2 Adsorbents

Carbon Foam-Reinforced Polyimide-Based Carbon Aerogel Composites Prepared via Co-Carbonization as Insulation Material

Synthesis of porous polyimide films with low dielectric constant and excellent mechanical properties by ambient pressure drying

Poly(ionic Liquid)s As New Materials for CO2 Absorption

Insight into the role of ionic liquid for improving silica aerogel performance in CO 2 adsorption

Sponge-like polyethyleneimine adsorbents with interconnected open channels enabling ultra-high CO 2 adsorption and separation capacity

Modulated Synthesis of N-doped Porous Carbons Via Rational Design of the Poly(ionic Liquid) Precursors Towards Efficient CO2 Separation