Abstract:Although fly ash foam concrete (FAFC) is lightweight, heat-retaining, and insulating, its application options are constrained by its weak construction and short lifespan. The effects of various dosage ratios of the foaming agent (i.e., hydrogen peroxide), silica fume, and polypropylene fiber on the dry density, compressive strength, thermal insulation performance, pore structure parameters, and durability of FAFC were analyzed in this study, which sought to address the issues of low strength and low durability of FAFC. According to the findings, there is a negative correlation between the amount of hydrogen peroxide (as the foaming agent) and compressive strength, and, as the silica fume and polypropylene fiber (PP fiber) content rise, the strength will initially rise and then fall. The distribution of pore sizes gradually shifts from being dominated by small pores to large pores as the amount of foaming agent increases, while the porosity and average pore size gradually decrease. When the hydrogen peroxide content is 5%, the pore shape factor is at its lowest. The pore size distribution was first dominated by a small pore size and thereafter by a large pore size when the silica fume and PP fiber concentration increased. Prior to increasing, the porosity, average pore size, and pore shape factor all decreased. Additionally, the impact of PP fiber on the freeze–thaw damage to FAFC was also investigated at the same time. The findings indicate that the freeze–thaw failure of FAFC is essentially frost heave failure of the pore wall. The use of PP fiber is crucial for enhancing FAFC's ability to withstand frost. The best frost resistance is achieved at 0.4% PP fiber content. In conclusion, the ideal ratio for overall performance was found to be 5% hydrogen peroxide content, 4% silica fume content, and 0.1% polypropylene fiber content. The results obtained could be applied in different fields, such as construction and sustainable materials, among others.

Alkali-activated fly ash foam concrete with Yellow River silt: Physico-mechanical and structural properties

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

Evaluation on Reactivity of Fly Ash from Different Sources in Alkali Activated System-Progressing Environmentally Construction Through Waste Utilization

Utilization of ultra-fine dredged sand from the Yangtze River in alkali-activated slag/fly ash mortars: Mechanical properties, drying shrinkage and microstructure

Study on the Performance of Foam Concrete Prepared from Decarburized Fly Ash

Inhibitory mechanism of fly ash on alkali-silica reactivity of siliceous rock fine aggregate: A case study of Yangxi concrete dam

Fresh and Hardened Properties of Alkali-Activated Fly Ash/slag Binders: Effect of Fly Ash Source, Surface Area, and Additives

Preparation of foam concrete from solid wastes: Physical properties and foam stability

Utilization of Calcium Carbide Residue as Solid Alkali for Preparing Fly Ash-Based Geopolymers: Dependence of Compressive Strength and Microstructure on Calcium Carbide Residue, Water Content and Curing Temperature

Preparation and characterization of foam ceramics from red mud and fly ash using sodium silicate as foaming agent

Development of Environmentally Friendly and Economical Flood-Prevention Stones Based on the Sediments of the Yellow River

Microstructure and macro properties of sustainable alkali-activated fly ash mortar with various construction waste fines as binder replacement up to 100%

In-Depth Insight into the Effects of Steel Slag and Calcium Hydroxide on the Properties of a Fly Ash-Red Mud Geopolymer

Effect of Fly Ash and Alkaline Solution on Rheology of Foamed Concrete

Effect of calcination pretreatment on mechanical properties of alkali-activated artificial stone incorporating Yellow River silt

Effects of Silica Fume/ultrafine Fly Ash on the Rheology and Hardening of Alkali-Activated Slag-Waste Ceramic Powder Paste

Innovative use of solid CO2 as an eco-friendly additive in alkali-activated concrete for enhancing its performance

Mechanical Properties and Mechanism of Geopolymer Cementitious Materials Synergistically Prepared Using Red Mud and Yellow River Sand

Microstructure, strength development mechanism, and CO2 emission analyses of alkali-activated fly ash-slag mortars

Circulation Fluidized Bed Combustion Fly Ash as Partial Replacement of Fine Aggregates in Roller Compacted Concrete

Investigating the Mechanical and Durability Characteristics of Fly Ash Foam Concrete