Abstract:Installation of renewable energy to building heating systems with cost-effective and affordable ways is becoming an ever-growing factor. Heat pump (HP) is a high energy efficient renewable energy device which can be a renewable-based alternative to fossil fuel boilers in buildings. Air source heat pumps (ASHPs) as a promising solution achieve the carbon reduction target in the domestic sector, but the limitation of electricity consumption and low supply flow temperatures (for most of the standard ASHPs the supplied heat temperature is around 55 °C) will hinder the implementation of ASHP for domestic applications and replace the existing fossil boiler. With 20% of households using heat pumps, the peak grid demand increases by 7.5 GW (14%) making extra burden to the grid. However, the low temperature water supply by ASHP can benefit to the underfloor heating in the building, which provides the most indoor thermal comfort environment. The building integration of photovoltaics (BIPV) is another type of renewable energy, where the PV elements actually become an integral part of the building, by simultaneously serving as building envelope material and acting as power generator. There is a growing consensus that the generated electricity by photovoltaic should provide electricity at the point of use, therefore the BIPV power can be used to drive ASHP. However, the on-site production of solar electricity is an intermittent source, typically the greatest may not be at or near the time of a building’s peak loads for residential demanding. A thermal store is necessary for storing the heat produced by ASHP during the daytime and discharge the heat for later usage. In addition, the high temperature in BIPV need to be regulated in order to avoid the reduction of the solar power conversion efficiency. Phase change materials (PCMs) absorb a large amount of energy as latent heat at a relative constant phase transition temperature and are thus used for passive heat storage and temperature control. PCMs incorporated into BIPV and underfloor heating system in buildings may be suitable for regulating the PV temperature rising and storing the heat from ASHP for underfloor heating.A two-dimensional temperature-based finite-volume numerical simulation model has been developed and experimentally validated for PCM energy store and temperature regulation. Using electricity generated by BIPV to drive the ASHP and store the thermal energy to thermal mass of PCM in underfloor heating system has been studied considerably in this paper. It has been found that the effect of using cooling coil of ASHP (evaporator) to augment the temperature regulation in BIPV keeps PV electricity efficiency at a high level. This paper summarises the results of a detailed theoretical investigation and analysis of solar energy production and storage control in buildings. An optimised combination of using solar power to drive ASHP and store the heat in PCM for underfloor heating could improve the energy efficiency of PV through temperature regulation and may achieve a cost-effective and affordable heating system the building.

Synergetic performance improvement of a novel building integrated photovoltaic/thermal-energy pile system for co-utilization of solar and shallow-geothermal energy

A Hybrid Parabolic Trough Solar Collector System Integrated with Photovoltaics

Prospective Study of a Novel Heat Pump System with Solar Energy Spectral Beam Splitting

Hybrid photovoltaic/thermal and ground source heat pump: Review and perspective

Research on renewable energy coupling system based on medium-deep ground temperature attenuation

A hybrid photovoltaic and water/air based thermal(PVT) solar energy collector with integrated PCM for building application

Thermal performance and energy flow analysis of a PV/T coupled ground source heat pump system

Optimal Coordination of Photovoltaic/Thermal Collectors and Ground-source Heat Pumps in Integrated Energy Systems*

Enhancing Long-Term Viability of Energy Pile with Heat Sink Systems in Tropical Monsoon Climates: Implementation Strategies and Performance Analysis

Performance Evaluation and Optimization of a Novel System Combining a Photovoltaic/Thermal Subsystem & an Organic Rankine Cycle Driven by Solar Parabolic Trough Collector

Thermal Performance of Energy Piles in Unsaturated Soils: Experiment, Simulation, and Case Study

Study on the Performance of Photovoltaic/Thermal Collector–Heat Pump–Absorption Chiller Tri-Generation Supply System

Improving thermal performance of groups of energy screw piles with phase change materials

Analysis of coupling characteristics of clean heating systems based on complementary solar, geothermal, and wind energy

Performance Analysis of Multi-energy Complementary Heating System Based on Photo-voltaic/thermal collectors and Heat Pumps

Enhancing Energy Utilisation in Building with Combining Building Integrated PV and Air Source Heat Pump for Underfloor Heating Using Phase Change Materials

Collaborative configuration and optimal operation of cogeneration system based on phase change heat storage

Co-generation ability investigation of the novel structured PVT heat pump system and its effect on the “Carbon neutral” strategy of Shanghai

Performance analysis of solar assisted heat pump coupled with build-in PCM heat storage based on PV/T panel

Thermodynamic analysis of a hybrid energy system coupling solar organic Rankine cycle and ground source heat pump: Exploring heat cascade utilization

Photovoltaic Thermal Module and Solar Thermal Collector Connected in Series to Produce Electricity and High-Grade Heat Simultaneously