Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Block masonry equation-based model updating of a masonry minaret and seismic performance evaluation

Field Observations and Numerical Investigations on Seismic Damage Assessment of RC and Masonry Minarets During the February 6th, 2023, Kahramanmaraş (Mw 7.7 Pazarcık and Mw 7.6 Elbistan) Earthquakes in Türkiye

Effects of Velocity Pulse-Like Ground Motions on the Seismic Failure Behavior of Masonry Minarets

Evaluation of the seismic performance pre- and post-restoration of a masonry clock tower's FE model updated via experimental and optimization methods

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Seismic analysis of Islamic Egyptian minarets through 3D scanning and dynamic simulation

Model updating of Masonry courtyard walls of the historical Isabey mosque using ambient vibration measurements

Numerical and Experimental Investigation on Cyclic Behavior of Masonry Infill Walls Retrofitted with CFRP

Different Soil-Structure Interaction Modelling Strategies for Seismic Analysis of a Masonry Church

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Dynamic characteristics of stone masonry walls before and after damage: Experimental and numerical investigations

Numerical analysis of the brick shape and bond pattern effects on the masonry cyclic behavior: a new brick shape to improve the masonry seismic performance

Structural condition assessment with structural health monitoring systems and nonlinear simplified models

Damage to monumental masonry buildings in Hatay and Osmaniye following the 2023 Turkey earthquake sequence: The role of wall geometry, construction quality, and material properties

Seismic damage evaluation of historical masonry towers through numerical model

An application of finite element model updating for damage assessment of a two-story reinforced concrete building and comparison with lidar

Seismic performance of masonry structures after 06 February 2023 earthquakes; site survey and FE modelling approach

Numerical Modeling of Masonry Infilled Reinforced Concrete Building during Construction Stages Using ABAQUS Software

Operational modal analysis, seismic vulnerability assessment and retrofit of a degraded RC bell tower

Backbone Model for Confined Masonry Walls for Performance-Based Seismic Design

Experimental and numerical investigation of hysteretic earthquake behavior of masonry infilled RC frames with opening strengthened by adding rebar-reinforced stucco