Abstract:Aluminium metal-matrix composites are broadly employed in industries like aerospace, marine, automobile-sector, and many others, generating a broad research interest. They are preferred for their high strength and low wear rate. This research work is mainly directed towards the fabrication of two types of metal-matrix composite materials using aluminium-alloy 6061(AA6061) as the matrix material and incorporating aluminium oxide (Al 2 O 3 ), aluminium nitride (AlN), and silicon carbide (SiC) as a reinforcement material. AA6061 has been reinforced with Al 2 O 3 and SiC particulates in AS series composites, while AA series composites, AA6061 has been reinforced with Al 2 O 3 and AlN particulates. This hybrid metal composite was constructed using the stir-casting method. These hybrid composites have been investigated for their physical and mechanical characteristics , viz. density, hardness, impact strength , void content, flexural strength, and tensile strength following the ASTM standards. Tribological characteristics of these hybrid composites were performed by Pin-on-disc (POD) tribometer. Taguchi's design of experimental technique was applied taking four factors viz. composition, sliding-velocity (SV), sliding-distance (SD), and load, and each having 4 levels. ANOVA was employed to find out meaningful parameters. SEM analysis of worn-surface was executed to find out the dominant wear mechanism. Experimental density was highest for AS42, and AA42 composites and void content were lowest for the same. Mechanical properties viz. density, hardness, impact strength, void content, flexural strength, and tensile strength were higher than the base alloy. From the response table of Taguchi analysis of AS and AA composite, the load factor significantly impacted the specific wear rate (SWR) to follow filler content (FC). It can be followed from the ANOVA table for AS composite that the load factor had a magnificent impact on the SWR. The SV and SD show no significant effect on SWR.

Investigation of wear and friction behavior of stir rheocast AA2024/TiB2 composite using Taguchi approach

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Study of Wear Behavior on AA6061 Reinforced with Hybrid Ceramic Composites through Optimization

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Microstructural characterization and tribological behavior of surface composites fabricated on AA7050-T7451 alloy via friction stir processing

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Mechanical Behavior and Sliding Wear Assessment of Al2024/TiC Metal Matrix Composite using Taguchi and Spotted Hyena Optimization

Microstructure, hardness, and wear resistance of AA5083/Ti3SiC2 composites fabricated via friction stir processing

Prediction of tribological performance of AA8011/wt.%ZrO2 based composites fabricated by stir casting route

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

Influence of wear parameters on friction performance of A356 aluminum – graphite/ granite particles reinforced metal matrix hybrid composites

Development, mechanical characterization and analysis of dry sliding wear behavior of AA6082–Metakaolin metal matrix composites

Evaluation of Dry Sliding Wear Properties of Stir Cast AA7050/10B4C Composites Through Fuzzy-ARAS

Modeling of wear performance and surface roughness of AA6061-T6/B4C composite under dry sliding conditions by RSM

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

A study of processing and parametric optimization of wear-resistant AZ91-TiB2 composite fabricated by ultrasonic-assisted stir casting process

Analysis of Wear Behaviour of AA5052 Alloy Composites by Addition Alumina with Zirconium Dioxide Using the Taguchi-Grey Relational Method

Dry sliding wear behaviour of AA6082/BN/Mos2 hybrid metal matrix composites synthesized using stir casting process

Microstructure and tribological behavior of Al-TiC composite strips fabricated by a multi-step densification method

Multi-response optimisation of wear parameters of B4C reinforced Al-Fe-Si composites: Using Taguchi-grey relational analysis

Influence of the friction and wear performance of TiB2/7075 aluminum-based composite materials prepared by friction stir processing