Abstract:Lithium-ion batteries (LiBs) are a mature technology which has attracted much attention over the last three decades with the development of portable devices. With the increasing number of LiBs and their use in electric vehicles, there are persistent efforts to enhance their safety by identifying suitable substitutes for liquid non-aqueous electrolytes, which are highly flammable, volatile, and can cause leakage. To this end, gel polymer electrolytes (GPEs) represent a promising alternative. To be suitable in applications and maximize ionic conductivity, polymers must meet specific requirements, the most important ones being a low glass transition temperature (T g ) and a low crystallinity, as ions move faster in amorphous phase. Moreover, these polymers need to be electrochemically stable and provide mechanical resistance as well as flexibility to the GPE. To increase the conductivity, polymers with polar functional groups that can dissolve salts are required. Several polymers, like PEO or PAN have already been studied but one limitation is their high T g (above ambient temperature) as well as a high crystallinity which make them brittle and limit the ionic conductivity. To circumvent this limitation, we studied an amorphous polymer based on acrylonitrile monomers. This elastomer, HNBR (Hydrogenated Nitrile Butadiene Rubber), was previously studied by our group and was shown to be thermally cross-linkable, leading to a polymer chemically resistant to electrolytes and electrochemically stable over a wide potential range. Hence, we propose to investigate thermally cross-linked HNBRs to gain a better understanding on the effect of interactions between polar nitrile functions and lithium ions and finally use this system as a GPE for Li-ion battery. To do so, a three-component system comprising HNBR:solvent:LiTFSI was studied to pinpoint the correct ratio to provide the GPE with competitive conductivity. Infrared spectroscopy was used to shed light on the interactions between nitriles and lithium ions while PFG-NMR was utilized to obtain spin-lattice relaxation times (T 1 ) and diffusion coefficients of 7 Li and 19 F for various HNBR-based GPEs. These results were correlated to EIS measurements and among the GPEs tested, those composed of 2M LiTFSI in propylene carbonate and HNBR with an acrylonitrile content of 50% are the most promising. This study highlights the benefits of high acrylonitrile content in the polymer and the use of a solvent with moderate donor number to promote interactions between nitriles and Li + .

Flexible gel polymer electrolyte comprising high flash point solvent adiponitrile with ethylene carbonate as co-solvent for sodium-ion batteries

A Gel Polymer Electrolyte with High Uniform Na+ Flux and its Constructed Hybrid Interface Synergistically to Facilitate High-Performance Sodium Batteries

A sodium ion conducting gel polymer electrolyte with counterbalance between 1-ethyl-3-methylimidazolium tetrafluoroborate and tetra ethylene glycol dimethyl ether for electrochemical applications

Mg‐Ion Conducting Gel Polymer Electrolyte Based on High Flash Point Solvent Adiponitrile for Magnesium Ion Batteries

Interface‐Compatible Gel‐Polymer Electrolyte Enabled by NaF‐Solubility‐Regulation toward All‐Climate Solid‐State Sodium Batteries

Gel polymer electrolyte composites in sodium-ion batteries: Synthesis methods, electrolyte formulations, and performance analysis

High‐performance sodium ion conducting gel polymer electrolyte based on a biodegradable polymer polycaprolactone

In-situ constructing efficient gel polymer electrolyte with fluoride-rich interface enabling high-capacity, long-cycling sodium metal batteries

Competitive Solvation Structures via Hetero‐Salt Additive Strategy Enables Temperature‐Adaptive Sodium‐Ion Batteries

Synthesis and assessment of novel Na 2 S dispersed high performance nanocomposite gel polymer electrolyte intended for sodium batteries and electric double layer capacitors

Facile Design of Asymmetric Flame-Retardant Gel Polymer Electrolyte with Excellent Interfacial Stability for Sodium Metal Batteries

Effects of Comonomers on the Performance of Stable Phosphonate-Based Gel Terpolymer Electrolytes for Sodium-Ion Batteries with Ultralong Cycling Stability

Cross-Linked Polyacrylonitrile-Based Elastomer Used as Gel Polymer Electrolyte in Li-Ion Battery

Anion-Immobilized Gel Polymer Electrolyte with a High Ion Transference Number for High-Performance Lithium/Sodium Metal Batteries

Gel Polymer Electrolyte Made of an Amorphous Polyacrylonitrile-Based Elastomer

Conductive Na2Zn2TeO6 Filler Modified Gel Polymer Electrolyte Membranes for Application in Sodium‐Ions Batteries

A P(VDF-HFP) and nonwoven-fabric based composite as high-performance gel polymer electrolyte for fast-charging sodium metal batteries

Liquid Electrolyte Immobilized in Compact Polymer Matrix for Stable Sodium Metal Anodes

Understanding Na + Diffusion, Physicochemical Behavior, and Electrochemical Performance of a Gel Polymer Electrolyte

Highly Conductive PEO-Based Polymer Composite Electrolyte for Na Battery Applications