Abstract:The paper investigated the effect of selected processing conditions during gear grinding on the value and distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment (TCT) conducted by a continuous single-piece flow method.The gears were carburised with LPC at 920C, then quenched in a 4D Quenching chamber at 7 bar and tempered at 190C for 3 hours. In the next step, the working surfaces of the gear teeth were ground by supplying grinding fluid (GF) to the grinding zone using the WET method and the MQL method with a minimum amount. Measurements were made on the distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment and after the grinding process.The results of the study showed the influence of workpiece speed vw and the method of delivery to the grinding zone GF on selected parameters describing the condition of the technological surface layer of the teeth of gears made of 20MnCr5 steel. The grinding process with a white aluminium oxide grinding wheel causes deterioration in the material's residual stress state. For each of the three analysed workpiece speeds vw, smaller changes in microhardness with respect to the microhardness of the material before grinding occur in the surface layer of samples ground with GF fed with the MQL method. Similarly, residual stress values are in the area of favourable compressive stresses.Environmental considerations and the need to comply with increasingly stringent environmental protection and worker safety regulations are pushing researchers and entrepreneurs to completely eliminate or reduce the consumption of grinding fluids in the grinding process. Based on the research and analysis carried out in this study, it was concluded that applying minimum GF by the MQL method could be an alternative to the conventional WET method.In sustainable manufacturing, it is extremely important to produce high-quality items while reducing the cost of manufacturing and taking care of the environment and workers' health. This includes the manufacture of gears, a basic component used in gear transmissions in the automotive industry, for example. The research has established that it is possible to use the MQL method, which reduces the amount of GF used when grinding the working surfaces of gear teeth, as an alternative to the conventional WET method.The conducted research was the first to determine the most favourable conditions, in terms of the obtained residual stresses and microhardness, for grinding the working surface of gear teeth using the MQL method.

Analyzing micro-geometric deviations of a helical gear profile as a function of material and machining parameters in the hobbing, shaving and carbonitriding processes

Engineering support for the manufacture of gears of aviation gas turbine engines providing for the instability of the physical and mechanical properties of their materials

Analysis on wear patterns and mechanisms of carbide tool for face-hobbing of spiral bevel gear

Modeling and Analysis of Deformation for Spiral Bevel Gear in Die Quenching Based on the Hardenability Variation

Optimization of Process Parameters for the Axial Distortion and Distortion Range During Die Quenching of a Spiral Bevel Gear

Profile Optimisation of a Solid Modular Hob in the Machining of Gears Made of Classic and Unusual, Innovative Materials

Size effects on process performance and product quality in progressive microforming of shafted gears revealed by experiment and numerical modeling

Experimental investigations on surface finish and microgeometry of helical gear in pulsed-electrochemical honing process

Effect of grinding conditions of gears made of 20MnCr5 steel after single-piece flow heat treatment on the condition of the surface layer of the tooth working surface

The effect of gear-manufacturing quality on the mechanical and thermal responses of a polymer-gear pair

Analysis and Kinematic Modeling of Ausform-Finishing Process for Manufacturing Hardened Gears

Experimental Investigation on Microstructure Alteration and Surface Morphology While Grinding 20cr2ni4a Gears with Different Grinding Allowance Allocation

Investigation of non-uniformity of temperature distribution and phase transformation in spiral bevel gears during carburizing and quenching

Shear cutting induced residual stresses in involute gears and resulting tooth root bending strength of a fineblanked gear

Micro- and Macroscopic Analysis of Fatigue Wear of Gear Wheel Top Layer-An Impact Analysis of Thermochemical Treatment

Influence of cryogenically treated hob on surface characteristics of spur gear

Experimental Method of Machining Gears with an Involute Profile Using CNC Lathe with Driven Tools

Optimizing Wire Electrical Discharge Machining Parameters for Enhanced Gear Machining Performance: A Machine Learning Approach on 20MnCr5 Steel

Machining deformation control methods and analysis of a thin-walled gear spoke plate

Study on precision isothermal micro forming technology of aluminum alloy micro-gears

Influences of tooth flank finishing after fine particle shot peening on tooth surface texture and fatigue life of vacuum carbonitrided gears