Abstract:Introduction Cadmium usually exists in nature as a compound and under normal environmental conditions, its small content will not affect human health. Nevertheless, with human society's development, heavy metal ions pollution has become substantially serious, and they have serious biological toxicity. Hence, it is important to develop simple, rapid, sensitive, and portable devices for Cd 2+ sensing [1]. In the present work, we show how paper based microfluidic sensors improve sensitivity and limit of detection (LOD) in comparison to classical screen-printed carbon-based electrode (SPCE). Furthermore, the presented microfluidic electrochemical carbon-based sensor (μCS) do not employ critical metals and rely on graphite foil that is modified by N-doped carbon nanoonions (N-CNOs) N-CNOs. Experimental For the synthesis of N-doped CNOs the Kuznetsov method was employed [2]. The alignment of the component for μCS device is sketched below. After providing the analyte solution through the sponge the electrochemical detection is carried out through accumulation of the metal at the working electrode for varying times and cathodic potentials. The final detection is carried out through square wave anodic stripping voltammetry (SWASV) of the accumulated metal. Results and discussion To realize a sensitive measurement, some experimental conditions including the optimal amount of the employed N-doped CNOs and Nafion in the nanocomposite, deposition time and potential, and the effect of pH of supporting electrolyte were studied. By increasing the deposition time ranging from 0 to 5 min, the SPCE/N-CNOs signal was increased and after that, it remains roughly constant because the WE surface is being saturated and also the amount of analyte in the droplet was reduced due to the presence of a stagnant flow. However, for μCS/N-CNOs by increasing the accumulation time ranging from 0 to 10 min the signal was increased which shows that the electrode surface is still far from being saturated (because of the live flow). A linear concentration range from 1.0 to 100.0 μg L - 1 was achieved using SWASV. Also, the LOD and sensitivity are calculated to be 0.5 μg L - 1 and 1.02 μA μM -1 cm -2 , respectively. Additionally, the method was successfully employed for measurements of Cd 2+ in different real samples, which demonstrated the excellent applicability of the device for the adsorption and detection of heavy metal ions. Conclusion The μCS/N-CNOs offers several core advantages over SPCE/N-CNOs in terms of cost, simplicity, analysis time, and sensitivity. These unique advantages are due to the combined microfluidic configuration, 3D electrode layout, and a unique modifier. We believe our findings would have significant implications in developing other portable, fast, and cost-effective electrochemical detection platforms, such as clinical diagnosis and security inspection. References [1]. Fan, Guojing, Dasun Zhai, and Dongsheng Zou. "Highly sensitive electrochemical determination of cadmium (II) in environmental water based on the electrodeposited bismuth nanoparticles." Int. J. Electrochem. Sci 11 (2016): 4362-4370. [2]. Krishnamurthy, S., et al. "In situ formation of onion-like carbon from the evaporation of ultra-dispersed nanodiamonds." Carbon 52 (2013): 145-149. Figure 1

Activated carbon based paste electrodes for the simultaneous and effective detection of divalent cadmium and lead ions in wastewater

Enhancing Heavy Metal Detection through Electrochemical Polishing of Carbon Electrodes

Bismuth-Coated Thick-Film Carbon Electrodes for the Detection of Lead and Cadmium by Anodic Stripping Voltammetry

Selective and simultaneous detection of cadmium, lead and copper by tapioca-derived carbon dot–modified electrode

Simultaneous quantification of cadmium and lead ions using β-cyclodextrin functionalized poly(amino acid) electrochemical sensor

A Highly Sensitive Electrochemical Sensor for Cd2+ Detection Based on Prussian Blue-PEDOT-Loaded Laser-Scribed Graphene-Modified Glassy Carbon Electrode

Rapid detection of heavy metal ions based on a novel BMIMPF6-MWCNTs/GCE sensor and square wave voltammetry in actual water samples

Electrochemical Sensing of Lead in Drinking Water Using MWCNTs and \b{eta}-Cyclodextrin

rGO/MWCNTs-COOH 3D hybrid network as a high-performance electrochemical sensing platform of screen-printed carbon electrodes with an ultra-wide detection range of Cd(II) and Pb(II)

Increasing Sensitivity and Selectivity for Heavy Metal Sensing through Microfluidic Electrochemical Sensor

Simultaneous and Sensitive Detection of Cd(II) and Pb(II) Using a Novel Bismuth Film/Ordered Mesoporous Carbon-molecular Wire Modified Graphite Carbon Paste Electrode

A novel electrochemical sensor modified with carbon nanocomposites and ion‐imprinted polymers and its high selectivity for cadmium ion detection in real samples

Ultra-sensitive detection of cadmium and lead in water using crown ether gel electromembrane extraction coupled with miniaturized electrochemical system

Hybrid hierarchically porous carbon micron tubes for trace cadmium and lead ions electrochemical detection

Iron terephthalate MOF-MWCNTs based composite paste two-electrode system for selective detection of lead in contaminated stream

Fabrication of a graphite-paraffin carbon paste electrode and demonstration of its use in electrochemical detection strategies

An Efficient Electrochemical Sensor Based on Three-Dimensionally Interconnected Mesoporous Graphene Framework for Simultaneous Determination of Cd(Ii) and Pb(Ii)

Mesoporous carbon decorated with MIL-100(Fe) as an electrochemical platform for ultrasensitive determination of trace cadmium and lead ions in surface water

An efficient self-made paper-based carbon electrode for electrochemical detection of heavy metal ions

Synthesis and Application of Sludge-Based Activated Carbon in the Efficient Removal of Cadmium (II) and Lead (II) from Wastewater

An electrochemical sensor for cadmium ion detection that is based on an AuNP-functionalized metal–organic framework-graphene nanocomposite