Abstract:Introduction Cadmium usually exists in nature as a compound and under normal environmental conditions, its small content will not affect human health. Nevertheless, with human society's development, heavy metal ions pollution has become substantially serious, and they have serious biological toxicity. Hence, it is important to develop simple, rapid, sensitive, and portable devices for Cd 2+ sensing [1]. In the present work, we show how paper based microfluidic sensors improve sensitivity and limit of detection (LOD) in comparison to classical screen-printed carbon-based electrode (SPCE). Furthermore, the presented microfluidic electrochemical carbon-based sensor (μCS) do not employ critical metals and rely on graphite foil that is modified by N-doped carbon nanoonions (N-CNOs) N-CNOs. Experimental For the synthesis of N-doped CNOs the Kuznetsov method was employed [2]. The alignment of the component for μCS device is sketched below. After providing the analyte solution through the sponge the electrochemical detection is carried out through accumulation of the metal at the working electrode for varying times and cathodic potentials. The final detection is carried out through square wave anodic stripping voltammetry (SWASV) of the accumulated metal. Results and discussion To realize a sensitive measurement, some experimental conditions including the optimal amount of the employed N-doped CNOs and Nafion in the nanocomposite, deposition time and potential, and the effect of pH of supporting electrolyte were studied. By increasing the deposition time ranging from 0 to 5 min, the SPCE/N-CNOs signal was increased and after that, it remains roughly constant because the WE surface is being saturated and also the amount of analyte in the droplet was reduced due to the presence of a stagnant flow. However, for μCS/N-CNOs by increasing the accumulation time ranging from 0 to 10 min the signal was increased which shows that the electrode surface is still far from being saturated (because of the live flow). A linear concentration range from 1.0 to 100.0 μg L - 1 was achieved using SWASV. Also, the LOD and sensitivity are calculated to be 0.5 μg L - 1 and 1.02 μA μM -1 cm -2 , respectively. Additionally, the method was successfully employed for measurements of Cd 2+ in different real samples, which demonstrated the excellent applicability of the device for the adsorption and detection of heavy metal ions. Conclusion The μCS/N-CNOs offers several core advantages over SPCE/N-CNOs in terms of cost, simplicity, analysis time, and sensitivity. These unique advantages are due to the combined microfluidic configuration, 3D electrode layout, and a unique modifier. We believe our findings would have significant implications in developing other portable, fast, and cost-effective electrochemical detection platforms, such as clinical diagnosis and security inspection. References [1]. Fan, Guojing, Dasun Zhai, and Dongsheng Zou. "Highly sensitive electrochemical determination of cadmium (II) in environmental water based on the electrodeposited bismuth nanoparticles." Int. J. Electrochem. Sci 11 (2016): 4362-4370. [2]. Krishnamurthy, S., et al. "In situ formation of onion-like carbon from the evaporation of ultra-dispersed nanodiamonds." Carbon 52 (2013): 145-149. Figure 1

Selective and simultaneous detection of cadmium, lead and copper by tapioca-derived carbon dot–modified electrode

Simultaneous quantification of cadmium and lead ions using β-cyclodextrin functionalized poly(amino acid) electrochemical sensor

Application of gold nanoparticles/polyaniline-multi-walled carbon nanotubes modified screen-printed carbon electrode for electrochemical sensing of zinc, lead, and copper

High Sensitive On-Site Cadmium Sensor Based on Aunps Amalgam Modified Screen-Printed Carbon Electrodes

Highly selective simultaneous electrochemical detection of trace level of heavy metals in water samples based on the single-crystalline Co3O4 nanocubes modified electrode

Efficient sensor based on CeCo3O6 nanocomposite for the electrochemical detection of cadmium and copper ions

A Simple Strategy For The Detection Of Cu(Ii), Cd(Ii) And Pb(Ii) In Water By A Voltammetric Sensor On A Tc4a Modified Electrode

Simultaneous Determination of Cadmium(ii), Lead(ii) and Copper(ii) by Using a Screen-Printed Electrode Modified with Mercury Nano-Droplets

Increasing Sensitivity and Selectivity for Heavy Metal Sensing through Microfluidic Electrochemical Sensor

Tin nanoparticle-modified electrode for the simultaneous detection of cadmium (Cd) and lead (Pb) ions

A new electrochemical sensor based on a screen-printed electrode modified with an ion-imprinted PEDOT for the detection and the quantification of Cd(II)

UiO-66 Based Electrochemical Sensor for Simultaneous Detection of Cd(II) and Pb(II)

Thiol-based chemically modified carbon screen-printed electrode for simultaneous quantification of trace level Pb(II) and Cd(II)

Integrated polysaccharides via amidation for sensitive electrochemical detection of heavy metal ions

Development of a robust method for Cd(II) ions analysis using CeO2- and CeO2-Cu-BTC-based electrochemical sensors

Sensitive Stripping Determination of Cadmium(II) and Lead(II) on Disposable Graphene Modified Screen‐Printed Electrode

Electrochemical Detection of Cd2+, Pb2+, Cu2+ and Hg2+ with Sensors Based on Carbonaceous Nanomaterials and Fe3O4 Nanoparticles

Selective and sensitive visible-light-prompt photoelectrochemical sensor of Cu2+ based on CdS nanorods modified with Au and graphene quantum dots

Direct Electrodeposition of Carbon Dots Modifying Bismuth Film Electrode for Sensitive Detection of Cd 2+ and Pb 2+

A Tablet-Operated Portable Wireless Sensing Platform for Field Simultaneous Rapid Detection of both Cd (II) and Pb (II) Using CaAl-Layered Double Hydroxide Nanocomposite Modified Integrated Screen-Printed Three-Electrode

Copper Oxide Anchored Carbon Nanofibers: A Versatile Platform for Multiplex Detection of Antibiotics, Heavy Metals and Pesticides