Abstract:Effective thermal management is key to ensuring the reliable operation of high power electronic equipment. In this study, the strategy of phase transition and liquid cooling coupling applied to transient high power electronic equipment has been examined. In order to improve the performance of the phase changing material (PCM) in temperature control, the effects of the coupling structure have been addressed with a consideration of fin, copper foam (CF), graphite foam (GF), fin-copper foam (FCF) and fin-graphite foam (FGF) structures in heat dissipation. In this study, pure paraffin wax (PPW) was used as phase change material to prepare heat sinks based on the above five structures. The experimental study investigates the impact of different thermal conductivity strategies on temperature control characteristics, with a focus on cold capacity recovery and the combined phase change and liquid cooling, using pure paraffin wax module as a reference. The results have revealed that the fin-foam coupling structure delivers a better PCM performance than the single fin or foam structure. Operating at a heating power of 10 W, 15 W and 20 W, the temperature control time of the FGF structure was increased by 13.6 %∼14.6 % relative to the GF structure. At 15 °C with flow rates of 1 L/min, 1.5 L/min, 2 L/min liquid cooling conditions, the cooling capacity recovery time was reduced by 18.8 %, 17.2 %, 19.7 %, respectively. In the phase-change liquid-cooling coupling temperature control experiment, the final temperature increase in the FGF system was 11.7 °C -15.2 °C lower than that of the GF system under the same water temperature and volume flow for a 50 W heat source. The incorporation of fins also enhanced the thermal conductivity strengthening capability of the copper foam and reduced the cold recovery time. Based on the comprehensive evaluation, the FGF structure demonstrates superior temperature control performance and cold recovery characteristics of PCM, making it an optimal strengthening method. Following closely are the FCF, GF, Fin and CF structures. Compared to pure paraffin modules, these five modules exhibit varying degrees of improvement in temperature control and cold capacity recovery efficiency. This study provides guidance for optimizing heat sink design based on PCM in electronic applications.

Phase change heat transfer in a vertical metal foam-phase change material thermal energy storage heat dissipator

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Numerical thermal performance assessment of phase change process in a PCM/foam-fins enclosure under various thermal conditions

Experimental study of heat transfer enhancement using metal foam partially filled with phase change material in a heat sink

Numerical simulation of heat transfer performance in an enclosure filled with a metal foam and nano-enhanced phase change material

Experimental Study on the Thermal Performance of a Finned Metal Foam Heat Sink with Phase Change Material

Localized heating element distribution in composite metal foam‐phase change material: Fourier's law and creeping flow effects

Numerical simulation of thermal performance of heat sink augmented with phase change material PCM integrated with solid and aluminum metal foam fins

Influence of the foam-fin structure on the thermal performance of a coupled phase change liquid cooling module

Pore-scale investigation on the heat-storage characteristics of phase change material in graded copper foam

Numerical investigation on thermal performance of phase change materials embedded in functionally graded metal foam

Investigation of Phase Change Material Integrated With High Thermal Conductive Carbon Foam Inside Heat Sinks for Thermal Management of Electronic Components

Discharge improvement of a phase change material‐air‐based thermal energy storage unit for space heating applications using metal foams in the air sides

Numerical simulation on thermal behavior of partially filled metal foam composite phase change materials

An experimental study for thermal management using hybrid heat sinks based on organic phase change material, copper foam and heat pipe

Thermal energy storage of phase change materials in the solidification process inside the quasi‐square heat exchanger: CFD simulation

Numerical Analysis on a Latent Thermal Energy Storage System with Phase Change Materials and Aluminum Foam

Study of Aluminum Foam Material For Heat Dissipation of Heat Source at Varying Heat Generation

Computational study of a latent heat thermal energy storage system enhanced by highly conductive metal foams and heat pipes

Design and study of metal foam parameters on whole melting-solidification cycle in phase change heat storage system

Improving phase change heat transfer in an enclosure filled by uniform and heterogenous metal foam layers: A neural network design approach