Abstract:The characterization of silicon carbide (SiC) by specific electrical atomic force microscopy (AFM) modes is highly appreciated for revealing its structure and properties at a nanoscale. However, during the conductive AFM (C-AFM) measurements, the strong electric field that builds up around and below the AFM conductive tip in ambient atmosphere may lead to a direct anodic oxidation of the SiC surface due to the formation of a water nanomeniscus. In this paper, the underlying effects of the anodization are experimentally investigated for SiC multilayers with different doping levels by studying gradual SiC epitaxial-doped layers with nitrogen (N) from 5 × 1017 to 1019 at/cm3. The presence of the water nanomeniscus is probed by the AFM and analyzed with the force-distance curve when a negative bias is applied to the AFM tip. From the water meniscus breakup distance measured without and with polarization, the water meniscus volume is increased by a factor of three under polarization. AFM experimental results are supported by electrostatic modeling to study oxide growth. By taking into account the presence of the water nanomeniscus, the surface oxide layer and the SiC doping level, a 2D-axisymmetric finite element model is developed to calculate the electric field distribution nearby the tip contact and the current distributions at the nanocontact. The results demonstrate that the anodization occurred for the conductive regime in which the current depends strongly to the doping; its threshold value is 7 × 1018 at/cm3 for anodization. Finally, the characterization of a classical planar SiC-MOSFET by C-AFM is examined. Results reveal the local oxidation mechanism of the SiC material at the surface of the MOSFET structure. AFM topographies after successive C-AFM measurements show that the local oxide created by anodization is located on both sides of the MOS channel; these areas are the locations of the highly n-type-doped zones. A selective wet chemical etching confirms that the oxide induced by local anodic oxidation is a SiOCH layer.

New strategy for impedance measurement of surface oxidation characteristic in ceramic fiber by controlling aspect ratio

Oxidation resistance improvement of carbon fiber nonwoven fabrics through SiC coating technology

Sandwich structure SiCf/Si3N4–SiOC–Si3N4 composites for high-temperature oxidation resistance and microwave absorption

In-situ SiC nanowires reinforced SiC-based multicomponent ceramic coating for protecting SiOC/CF composites

Oxidation differences on Si- versus C-terminated surfaces of SiC during planarization in the fabrication of high-power, high-frequency semiconductor device

Oxidation Kinetics and Its Impact on the Strength of Carbon Short Fiber Reinforced C/SiC Ceramics

SiC fibers with different diameters exhibiting excellent high-temperature resistance and oxidation resistance

Bio‐Inspired Microstructure Design to Improve Thermal Ablation and Oxidation Resistance: Experiment on SiC

SiC Doping Impact during Conducting AFM under Ambient Atmosphere

Siliconization elimination for SiC coated C/C composites by a pyrolytic carbon coating and the consequent improvement of the mechanical property and oxidation resistances

Multifunction properties of SiOC reinforced with carbon fiber and in-situ SiC nanowires

Enhanced antioxidation and microwave absorbing properties of SiC/SiO2 coating on carbon fiber

Improved antioxidative and mechanical properties of SiC coated C/C composites via a SiO2-SiC reticulated layer

High-temperature resistance and thermal insulation performance of continuous SiMOC ceramic fibers fabricated by the modified sol-gel method combined with dry spinning

Novel preparation of functional β-SiC fiber based In2O3 nanocomposite and controlling of influence factors for the chemical gas sensing

Enhanced microwave absorption performance originated from interface and unrivaled impedance matching of SiO 2 /carbon fiber

Oxidation of SiC fibers in water vapor

Synthesis and characterization of high-temperature resistant yttrium-doped lanthanum monazite coatings on SiC fibers

Feasibility study of ZrSiO4 as matrix and fiber interphase of SiC/SiC composite

Using in-situ conversed nano SiC to bond UHTC particles and construct anti-ablation coating

Effect of long-time annealing at high temperature on the microstructure and mechanical properties of different types of SiC fibers