Abstract:This study proposes an efficient, facile, and scalable strategy to synthesize in situ heteroatom-doped porous graphene via laser direct writing on the precursor-doped polyimide (PI) film, which is fabricated for the first time through incorporating PI powder and precursors with sodium carboxymethyl cellulose (CMC) binder by a drop-casting and low-temperature drying process. The resulting microsupercapacitors (MSCs) based on the as-prepared heteroatom-doped porous graphene exhibit remarkable capacitive performance. The typical boron-doped MSC prepared on borax-doped polyimide film possesses an ultrahigh areal capacitance of 60.6 mF cm–2 at 0.08 mA cm–2, which is approximately 20 times larger than that of undoped MSC. Furthermore, the boron-doped MSC has impressive cycling stability (with the capacitance retention of 96.3% after 20 000 cycles), exceptional mechanical flexibility, tunable capacitance, and voltage output through arbitrary modular serial and parallel integration. Besides, the nitrogen-doped porous graphene with excellent capacitive performance is also prepared by laser direct scribing on the sulfonated melamine-doped polyimide film, demonstrating excellent scalability and generality of this strategy. Hence, one-step laser direct writing on precursor-doped polyimide films can realize in situ heteroatom doping and generation of hierarchical porous graphene electrodes simultaneously, which opens a new avenue for the facile, cost-effective, and scalable fabrication of heteroatom-doped porous graphene, thus promising for MSCs and various flexible and wearable electronics at large-scale production.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c03219?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c03219</a>.Experimental section (materials characterization, electrochemical performance calculations, DFT calculations); photographs of LIG-B6 on PET, PMMA, and fabric substrates; SEM and TEM images of pure LIG electrodes; cross-sectional SEM images of LIG, LIG-B6, and LIG-N6 electrodes; pore size distribution of LIG and LIG-B6; Raman spectrum and a photograph of the PI/CMC film; C 1s, B 1s, and O 1s XPS speaks of LIG-Bx samples; sheet resistance and conductivity of LIG-Bx films; CV curves at scan rates from 10 to 200 mV s–1 and GCD curves at current densities from 0.08 to 1 mA cm–2 of LIG-B0, LIG-B4.5, and LIG-B7.5; SEM image of LIG-B7.5; water contact angles of LIG, LIG-B6, and LIG-N6; adsorption energy calculated by DFT of LIG-B6; volumetric capacitance and areal and volumetric Ragone plots of LIG-Bx; pore size distribution and Raman spectra of LIG-Nx; sheet resistance and conductivity of LIG, LIG-B6, and LIG-N6; GCD curves at current densities from 0.08 to 1 mA cm–2 of LIG-N3 and LIG-N9; atomic ratios of LIG-Bx; and comparison of capacitive performance of LIG-B6 with other MSCs (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c03219/suppl_file/am1c03219_si_001.pdf">PDF</a>)Three LIG-B6 MSCs connected in series light a timer (Video S1) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c03219/suppl_file/am1c03219_si_002.mp4">mp4</a>)This article has not yet been cited by other publications.

Chitosan Oligosaccharide Laser Lithograph: A Facile Route to Porous Graphene Electrodes for Flexible On-Chip Microsupercapacitors

Laser In Situ Preparation of S-Doped Porous Graphene for Flexible Microsupercapacitors

Laser-Induced Graphene Formation on Chitosan Derivatives toward Ecofriendly Electronics

Laser-induced fabrication of porous graphene for flexible planar microsupercapacitors with wide voltage window

Laser synthesis of superhydrophilic O/S co-doped porous graphene derived from sodium lignosulfonate for enhanced microsupercapacitors

Direct laser writing of MnO2 decorated graphene as flexible supercapacitor electrodes

All-solid-state Supercapacitors from Natural Lignin-Based Composite Film by Laser Direct Writing

CuO nanoparticles embedded in laser-induced graphene for flexible planar micro-supercapacitors

Transforming lignin into porous graphene via direct laser writing for solid-state supercapacitors

Tuning the Electronic and Electrochemical Properties of 3D Porous Laser‐Induced Graphene by Electrochemically Induced Deposition of Polyoxovanadate Nanoclusters for Flexible Supercapacitors

One‐Step Scalable Fabrication of Graphene‐Integrated Micro‐Supercapacitors with Remarkable Flexibility and Exceptional Performance Uniformity

Laser engraving and punching of graphene films as flexible all-solid-state planar micro-supercapacitor electrodes

Flexible Micro-Supercapacitors Assembled Via Chemically Reduced Graphene Oxide Films Assisted by a Laser Printer.

Hierarchical Porous Graphene Film: an Ideal Material for Laser-Carving Fabrication of Flexible Micro-Supercapacitors with High Specific Capacitance

Paper-based laser-induced graphene for sustainable and flexible microsupercapacitor applications

Laser-Induced Nitrogen-doped Graphene for High-Performance Flexible Supercapacitors

One-step sustainable preparation of laser induced S-doped graphene for assembly of high-performance supercapacitors

Fabrication of flexible planar micro-supercapacitors using laser scribed graphene electrodes incorporated with MXene

Laser In-Situ synthesis of metallic cobalt decorated porous graphene for flexible In-Plane microsupercapacitors

Facile and Scalable Fabrication of High-Performance Microsupercapacitors Based on Laser-Scribed In Situ Heteroatom-Doped Porous Graphene

Laser Direct Synthesis of Co/CoO Modified Graphene for High-Performance Microsupercapacitors