Abstract:Heterogeneous microstructure designs have attracted a great deal of attention, not only because they have the potential to achieve an ideal combination of two conflicting properties, but also because the processes involved in their fabrication are cost-effective and can be scaled up for industrial production. The process parameters in the preparation process have an important effect on the microstructure and properties of alloy members prepared by wire arc additive manufacturing (WAAM) technology. It was expected that the spatial heterogeneous microstructure with large microstructural heterogeneities in metals can be formed through changing the process parameters. In this work, homogeneous NiTi thin-walled component and heterogeneous NiTi thin-walled component were fabricated using WAAM technology by adjusting the heat input. The effects of deposition height and heat input on the microstructure, mechanical properties and wear properties of WAAM NiTi alloys were investigated. The results show that grains were gradually refined with the increase of deposition height in the homogeneous WAAM NiTi component. The ultimate tensile strength of homogeneous WAAM NiTi component increased from 606.87 MPa to 654.45 MPa and the elongation increased from 12.72% to 15.38%, as the increase of deposition height. Moreover, the homogeneous WAAM NiTi component exhibited excellent wear resistance, the coefficient of friction decreased from 0.760 to 0.715 with the increase of deposition height. Meanwhile, the grains in the heterogeneous WAAM NiTi component shows the finest grains in the central region. The ultimate tensile strength of the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 556.12MPa, 599.53MPa and 739.79MPa, and the elongations were 12.98%, 16.69%, 21.74%, respectively. The coefficient of friction for the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 0.713, 0.720 and 0.715, respectively. The microhardness and cyclic compression properties of the homogeneous components with higher heat input were better than those of the heterogeneous components for the same deposition height. The tensile yield strength, elongation and wear resistance of the heterogeneous components were superior compared to the homogeneous components. These results can be used to optimize the WAAM process parameters to prepare NiTi components with excellent mechanical properties.

Direct energy deposition for fabricating the bionic sandwich heterogeneous alloy 316-Cu-NiTi: Microstructure and wear mechanism

Achieving illustrious friction on a directed energy deposition 316/NiTi heterogeneous alloy with bionic Ni interlayer

Revealing the wear mechanism of NiTi alloy coatings with biomimetic sandwich structures by laser cladding

Exploring the Friction and Wear Mechanisms of Nickel Titanium Alloy Fabricated by Laser Powder and Wire-Based Directed Energy Deposition

Microstructure and mechanical properties of Ti 2 Ni alloy fabricated by direct energy deposition

Heterogeneous interfaces of aluminum bronze/Inconel 718 dissimilar alloys under different wire arc directed energy deposition sequences

Dual-interfacial alloying mechanism in Ti-steel laminated metal composite fabricated by wire-arc directed energy deposition using a Cu-Ni interlayer

Time-varying deposition strategy for comprehensive properties improvement of bionic bidirectional gradient NiTi alloy fabricated by laser directed energy deposition

Tribocorrosion Behavior of NiTi Biomedical Alloy Processed by an Additive Manufacturing Laser Beam Directed Energy Deposition Technique

Microstructure and mechanical properties of TC4/NiTi bionic gradient heterogeneous alloy prepared by multi-wire arc additive manufacturing

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy

Microstructural Analysis, Tribological, and Corrosion Behavior of Nix-Tiy Alloys Deposited Using μ-Plasma Additive Manufacturing Process

Direct Laser Fabricated in Situ TiC Particulate Reinforced Ni30Al20Fe Intermetallic Matrix Composite

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Microstructure and Tribocorrosion Properties of NiTi/AlNi2Ti Ternary Intermetallic Alloy

Microstructure and Mechanical Properties of Bimetallic Materials Containing Ceramic Particles Made Using Directed Energy Deposition

Corrosion and wear behavior of Ti-5Cu-xNb biomedical alloy in simulated body fluid for dental implant applications

Revealing microstructural evolutions, mechanical properties and wear performance of wire arc additive manufacturing homogeneous and heterogeneous NiTi alloy

Mechanical properties and corrosion resistance characterization of a novel Co36Fe36Cr18Ni10 high-entropy alloy for bioimplants compared to 316L alloy

Microstructural response and wear behaviour of Ti-6Al-4V impregnated with Ni/Al2O3 + TiO2 nanostructured coating using an electric arc

Characterization of microstructure, grain distribution, and tribocorrosion properties of NiTi-based alloy