Abstract:The Net Zero Emission scenario proposed by the International Energy Agency projects a required electrolytic generation of hydrogen equivalent to 3600 GW by 2050 [1], averaging to an annual installation of ~130 GW/a between 2023 and 2050. If this were to be provided by proton exchange membrane based water electrolyzers (PEM-WEs) based on platinum catalysts for the hydrogen evolution reaction (HER) and iridium catalysts for the oxygen evolution reaction (OER), the current PEM-WE noble metal requirements of ~0.7 g Ir /kW and ~0.3 g Pt /kW [1] would have to be drastically reduced in view of the noble metal supply constraints. As argued previously, for PEM-WEs to be sustainable on such a large scale would require to achieve platinum and iridium loadings of ~0.05 mg/cm 2 electrode [2,3]. While the former can be easily achieved due to the fast HER kinetics on Pt, the latter requires either ultra-thin OER catalyst layers or improved OER catalysts with a substantially reduced iridium packing density (in units of g Ir /cm 3 electrode ) [2], like the recently developed catalyst with a hydrous iridium oxide shell supported on a titanium oxide core (IrO x /TiO 2 ) [4,5]. In this contribution, we will discuss the effect of the design of membrane electrode assemblies (MEAs) and of the adjacent porous transport layers on PEM-WE performance. In general, the preparation of MEAs with low platinum loading cathodes is straightforward, due to the availability of carbon supported platinum catalysts (Pt/C) with a low Pt packing density. For the optimization of the ionomer content in the cathode electrode, however, its effect on the high current density performance and on the hydrogen permeation rate from cathode to anode have to be considered [6,7]. With regards to the anode electrode, we will further discuss the MEA design challenges when targeting ultra-low iridium loadings. In the case of the ultra-thin catalyst layers that result when using conventional OER catalysts, additional contact resistances between the anode catalyst layer and the titanium based porous transport layer (Ti-PTL) are observed [2]. As will be shown, these can be largely mitigated by the use of a titanium based microporous layer (MPL) coated on the Ti-PTL, highlighting the importance of the interface between the PTL and the anode catalyst layer. In case of using the above described IrO x /TiO 2 catalysts with low iridium packing density, their typically lower electrical conductivity also results in apparent contact resistances within and across the anode catalyst layer [4], which poses an additional constraint on the allowable range of the catalyst/ionomer ratio in the anode electrode. The interplay between the anode catalyst type, the anode ionomer content, and the type of interface between the anode electrode and the PTL (i.e., with and without MPL) will be discussed. References: [1] International Energy Agency (IEA), Global Hydrogen Review 2021 , (2021) . [2] M. Bernt, A. Siebel, H. A. Gasteiger; "Analysis of Voltage Losses in PEM Water Electrolyzers with Low Platinum Group Metal Loadings"; J. Electrochem. Soc. 165 (2018) F305. [3] C. Minke, M. Suermann, B. Bensmann, R. Hanke-Rauschenbach; “Is iridium demand a potential bottleneck in the realization of large-scale PEM water electrolysis?”; International Journal of Hydrogen Energy 46 (2021) , 23581. [4] M. Bernt, C. Schramm, J. Schröter, C. Gebauer, J. Byrknes, C. Eickes, H. A. Gasteiger; "Effect of the IrO x Conductivity on the Anode Electrode/Porous Transport Layer Interfacial Resistance in PEM Water Electrolyzers"; J. Electrochem. Soc. 168 (2021) 084513. [5] M. Möckl, M. F. Ernst, M. Kornherr, F. Allebrod, M. Bernt, J. Byrknes, C. Eickes, C. Gebauer, A. Moskovtseva, H. A. Gasteiger; "Durability investigation and benchmarking of a novel iridium catalyst in a PEM water electrolyzer at low iridium loading"; J. Electrochem. Soc. 169 (2022) 064505. [6] P. Trinke, G. P. Keeley, M. Carmo, B. Bensmann, R. Hanke-Rauschenbach; "Elucidating the Effect of Mass Transport Resistances on Hydrogen Crossover and Cell Performance in PEM Water Electrolyzers by Varying the Cathode Ionomer Content"; J. Electrochem. Soc. 166 (2019) F465. [7] M. Bernt, J. Schröter, M. Möckl, H. A. Gasteiger; "Analysis of Gas Permeation Phenomena in a PEM Water Electrolyzer Operated at High Pressure and High Current Density"; J. Electrochem. Soc. 167 (2020) 124502.

Perspectives on current and future iridium demand and iridium oxide catalysts for PEM water electrolysis

Elucidating Fundamental Structure-Function Relationships for Iridium Oxide Catalysts in PEM Water Electrolyzers

Influence of Different Operating Conditions on Iridium Dissolution in a Proton Exchange Membrane Water Electrolyzer

(Invited) Design, Performance Characterization, and Durability of an Iridium-Based OER Catalyst for PEM Water Electrolysis

Design of PEM water electrolysers with low iridium loading

Iridium on Conductive Support: Towards Low Iridium Anodes in PEM Electrolyzers

(Invited) Lowering the Noble Metal Requirement for PEM Water Electrolysis: Membrane Electrode Assembly and Porous Transport Layer Design Considerations

Unraveling the Most Relevant Features for the Design of Iridium Mixed Oxides with High Activity and Durability for the Oxygen Evolution Reaction in Acidic Media

High Performance and Durable Anode with 10‐Fold Reduction of Iridium Loading for Proton Exchange Membrane Water Electrolysis

Composite Anode for PEM Water Electrolyzers: Lowering Iridium Loadings and Reducing Material Costs with a Conductive Additive

Revolutionizing Green Hydrogen Production with Next Generation PEM Water Electrolyzer Electrodes

Proton Exchange Membrane Electrolysis Performance Targets for Achieving 2050 Expansion Goals Constrained by Iridium Supply

Pathway to Complete Energy Sector Decarbonization with Available Iridium Resources using Ultralow Loaded Water Electrolyzers

Advances and status of anode catalysts for proton exchange membrane water electrolysis technology

(Invited) Degradation and Poisoning of Proton-Exchange Membrane Water Electrolyzer Anode Catalysts

N/C doped nano-size IrO2 catalyst of high activity and stability in proton exchange membrane water electrolysis

Incorporation of PEDOT:PSS to Reduce Iridium Loading at Anode Catalyst Layer for Proton Exchange Membrane Water Electrolysis

(Invited) Comparing and Contrasting the Advantages and Challenges of Catalysts for Low Temperature AEM, AEL, and PEM Electrolysis

(Invited) Electron Microscopy Investigation of PEM Electrolyzer Degradation at Low Iridium Loadings

Durability Testing of Low-Iridium PEM Water Electrolysis Membrane Electrode Assemblies

(Invited) Understanding and Tuning the Cell Reversal Tolerance of PEM Fuel Cell Anodes: Application-Relevant Design Parameters for Precious Metals Catalysts