Abstract:Proton exchange membrane water electrolysis (PEM-WE) is a rapidly developing and promising technology for the production of green hydrogen from renewable energy [1]. For its large-scale application it is inevitable to substantially reduce the currently used high iridium loadings (on the order of 1 mg Ir /cm 2 ) required for the oxygen evolution reaction (OER) in PEM-WE anodes [2]. Furthermore, the interface between the anode catalyst layer and the porous transport layer (PTL) is of critical importance to reduce interfacial resistances and avoid additional performance losses [3]. For example, coating the titanium PTL at the anode with ultra-thin layers of iridium or platinum mitigates the growth of a TiO x passivation layer and improves the long-term durability of PEM water electrolyzers [4]. With regards to the electrode, Bernt et al. [5] and Böhm et al. [6] have shown for a TiO 2 -supported OER catalyst (based on a low-iridium-packing-density catalyst concept) that a reduced electrical conductivity of the catalyst material has a detrimental effect on the PEM-WE cell performance: severe interfacial contact resistances between the electrode and the PTL have been observed for anodes based on OER catalysts with a low electrical conductivity in combination with an uncoated titanium PTL, which can be mitigated by improving catalyst conductivity or by using a platinum-coated PTL. Since the ionomer in electrodes not only influences proton and oxygen/water transport, but also acts as a binder that can affect the electrical resistance of the electrode, the work presented herein aims for a better understanding of the influence of the ionomer content in low-loaded PEM-WE anodes on cell performance and on the interfacial resistances between the anode electrode and the PTL. A TiO 2 -supported IrO x catalyst with 33 wt.% iridium and low electrical conductivity (approximately one order of magnitude lower compared to a commercial TiO 2 -supported catalyst with 75 wt.% iridium) is examined in 5 cm2 single cells with titanium PTLs on the anode side. The ionomer content within the anode catalyst layer is varied between 6 and 38 wt.% at iridium loadings of ~0.3 mg Ir /cm2. The potentiostatic testing protocol includes electrochemical impedance spectroscopy (EIS) measurements and yields stable current densities at low to medium ionomer contents. In contrast, a rapid and severe decrease in cell performance is observed at high ionomer contents, and the EIS-spectra reveal a dynamic growth of interfacial contact resistances (see figure 1). Besides presenting a detailed performance and EIS analysis, we will investigate the effect of a protective platinum coating covering the titanium PTL on the development of contact resistances for the different ionomer contents. Further operando and ex situ analyses will be performed to differentiate between degradation effects of the PTL and the electrodes and to gain a better understanding of the occurring interfacial resistances. References: [1] A. Buttler, H. Spliethoff; "Current status of water electrolysis for energy storage, grid balancing and sector coupling via power-to-gas and power-to-liquids: A review"; Renewable and Sustainable Energy Reviews 82 (2018) 2440-2454. [2] M. Bernt, A. Siebel, H. A. Gasteiger; "Analysis of voltage losses in PEM water electrolyzers with low platinum group metal loadings"; J. Electrochem. Soc. 165 ( 2018) F305-F314. [3] K. Ayers, N. Danilovic, R. Ouimet, M. Carmo, B. Pivovar, M. Bornstein; "Perspectives on Low-Temperature Electrolysis and Potential for Renewable Hydrogen at Scale"; Annu. Rev. Chem. Biomol. Eng. 10 ( 2019) 219-239. [4] C. Liu, M. Shviro, A. S. Gago, S. F. Zaccarine, G. Bender, P. Gazdzicki, T. Morawietz, I. Biswas, M. Rasinski, A. Everwand, R. Schierholz, J. Pfeilsticker, M. Müller, P. P. Lopes, R.-A. Eichel, B. Pivovar, S. Pylypenko, K. A. Friedrich, W. Lehnert, and M. Carmo; "Exploring the Interface of Skin-Layered Titanium Fibers for Electrochemical Water Splitting"; Adv . Energy Mater. 11 (2021) 2002926. [5] M. Bernt, C. Schramm, J. Schröter, C. Gebauer, J. Byrkness, C. Eickes, H. A. Gasteiger; "Effect of the IrO x Conductivity on the Anode Electrode/Porous Transport Layer Interfacial Resistance in PEM Water Electrolyzers"; J . Electrochem. Soc . 168 (2021) 084513. [6] D. Böhm, M. Beetz, C. Gebauer, M. Bernt, J. Schröter, M. Kornherr, F. Zoller, T. Bein, D. Fattakhova-Rohlfing; “Highly conductive titania supported iridium oxide nanoparticles with low overall iridium density as OER catalyst for large-scale PEM electrolysis”; Applied Materials Today 24 (2021) 101134. Acknowledgements: This work was funded by the German Federal Ministry of Education and Research (BMBF) in the framework of the Kopernikus P2X project (funding number 03SFK2V0-2). The authors gratefully acknowledge Dr. Christian Gebauer (Heraeus Deutschland GmbH & Co. KG) for providing the 33 wt.% IrO x /TiO 2 catalyst material. Figure 1

Durability Testing of Low-Iridium PEM Water Electrolysis Membrane Electrode Assemblies

(Invited) Design, Performance Characterization, and Durability of an Iridium-Based OER Catalyst for PEM Water Electrolysis

High Performance and Durable Anode with 10‐Fold Reduction of Iridium Loading for Proton Exchange Membrane Water Electrolysis

(Invited) Lowering the Noble Metal Requirement for PEM Water Electrolysis: Membrane Electrode Assembly and Porous Transport Layer Design Considerations

Design of PEM water electrolysers with low iridium loading

Elucidating Fundamental Structure-Function Relationships for Iridium Oxide Catalysts in PEM Water Electrolyzers

Durable Membrane Electrode Assemblies for Proton Exchange Membrane Electrolyzer Systems Operating at High Current Densities

Investigations on high performance proton exchange membrane water electrolyzer

Composite Anode for PEM Water Electrolyzers: Lowering Iridium Loadings and Reducing Material Costs with a Conductive Additive

Catalyst Dissolution Analysis in PEM Water Electrolyzers during Intermittent Operation

(Invited) Novel Design of Low-Loaded Membrane Electrode Assemblies for Advanced Low-Temperature Water Electrolyzers

Influence of Different Operating Conditions on Iridium Dissolution in a Proton Exchange Membrane Water Electrolyzer

(Invited) Electron Microscopy Investigation of PEM Electrolyzer Degradation at Low Iridium Loadings

Influence of the Ionomer Content in Low-Loaded Anode Electrodes on Interfacial Resistances in Proton Exchange Membrane Water Electrolyzers

Incorporation of PEDOT:PSS to Reduce Iridium Loading at Anode Catalyst Layer for Proton Exchange Membrane Water Electrolysis

Durability Assessment of Roll-to-Roll Coated PEM Water Electrolysis Anodes

Insights into Interfacial and Bulk Transport Phenomena Affecting Proton Exchange Membrane Water Electrolyzer Performance at Ultra‐Low Iridium Loadings

(Invited) Degradation and Poisoning of Proton-Exchange Membrane Water Electrolyzer Anode Catalysts

Novel thin/tunable gas diffusion electrodes with ultra-low catalyst loading for hydrogen evolution reactions in proton exchange membrane electrolyzer cells

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

(Digital Presentation) Large–Scale High-Performance Low Catalyst Loaded Membrane Electrode Assemblies for Advanced Proton Exchange Membrane Water Electrolyzers