Abstract:Pure Titanium (Titanium grade 2) and Ti6Al4V (Titanium grade 5) alloys are commonly used biocompatible materials for medical bone implants and dental protheses. As some implants have to be removed after a certain amount of time after the implantation, the osteo repellent surface is one of the most important property for the removable bone implants such as bone screws and plates. On contrary, for the dental protheses the property of the most importance is osseointegration. Femtosecond laser treatment causes ablation and produces LIPSS ("laser induced periodic surface structures") which can consist of cones on macro scale and ripples on nano scale which showed structures and roughness similar to that of a bone. Therefore, surface modifications by electrochemical anodization and femtosecond laser could be seen as promising methods for improving both osteo-repellence and osteointegration properties of the bone implants and dental protheses. The aim of this work is electrochemical and surface characterization of the anodized Titanium and Ti6Al4V alloy treated by the femtosecond laser. Firstly, Titanium and Ti6Al4V samples were anodized potentiostaticaly up to 100V in 25% phosphoric acid solution for 120s. Following the potentiostatic anodization, samples were structured with femtosecond laser to produce micro cones and nano ripples on top of the cones. As a final step, laser treated spots were potentiodynamicaly anodized using a SDCM (Scanning Droplet Cell Microscopy) setup. Influence of different potentials, scan rates and electrolytes were studied and optimized, consequently. Morphology and topography were examined by the means of SEM (Scanning Electron Microscopy) and AFM (Atomic Force Microscopy), while crystallography was determined by the XRD (X-Ray Diffraction). Furthermore, the composition of the oxide layer was determined by the XPS (X-ray photoelectron spectroscopy). Oxide forming factor (k ox ), a relative permittivity ε r , and ECSA (Electrochemical surface area) were obtained from the cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) experimental data. Electrochemical impedance spectroscopy data was modeled and compared between not preanodized, preanodized and anodized and not anodized after femtosecond laser structuring. Finally, bioassessment with osteoblast was done to examine the growth of the osteoblast cells on the modified surface structures. Value of the oxide forming factor (k ox ) for the pure Titanium and Titanium grade 5 were successfully calculated and compared with a Scanning Electron Microscopy. Calculated values of the relative permittivity ε r are in agreement with the literature values. Finally, obtained results indicate that anodized and subsequently femtosecond laser treated samples could be used as medical bone and dental implants.

Evaluation of the effect of diode laser application on the hydrophilicity, surface topography, and chemical composition of titanium dental implant surface

The effects of diode and Er:YAG laser applications on the surface topography of titanium grade 4 and titanium zirconium discs with sand-blasted and acid-etched (SLA) surfaces

Effect of Electrocautery and Laser Treatment on the Composition and Morphology of Surface-Modified Titanium Implants

The Impact of Mechanical Debridement Techniques on Titanium Implant Surfaces: A Comparison of Sandblasted, Acid-Etched, and Femtosecond Laser-Treated Surfaces

Influence of Dental Titanium Implants with Different Surface Treatments Using Femtosecond and Nanosecond Lasers on Biofilm Formation

Cell Response of Titanium Implant with a Roughened Surface Containing Titanium Hydride: an in Vitro Study

Effects of decontamination solutions on the surface of titanium: investigation of surface morphology, composition, and roughness

In Vitro And In Vivo Evaluation Of Sla Titanium Surfaces With Further Alkali Or Hydrogen Peroxide And Heat Treatment

Effect of Different Surface Treatments on Titanium Dental Implant Micro-Morphology

CO2-Laser Irradiation Affects Positively Surface Energy of Rough Titanium Surfaces

Bacterial reduction and temperature increase of titanium dental implant models treated with a 445 nm diode laser: an in vitro study

Development of Microstructure on Titanium Implant Surface Using CO2 Laser Processing

Optimizing surface properties in pure titanium for dental implants: a crystallographic analysis of sandblasting and acid-etching techniques

Influence of Er:YAG laser irradiation on surface properties of Ti-6Al-4V machined and hydroxyapatite coated

Electrochemical Surface Characterization of a Femtosecond Laser Treated and Anodized Ti and Ti6Al4V Alloy for Bone and Dental Implants

The Efficacy of a Diode Laser on Titanium Implants for the Reduction of Microorganisms That Cause Periimplantitis

Effects of Surface Conditions of Titanium Dental Implants on Bacterial Adhesion

Esthetic and Physical Changes of Innovative Titanium Surface Properties Obtained with Laser Technology

Influence of eight debridement techniques on three different titanium surfaces: A laboratory study

Comparison of antimicrobial effect of several decontaminating methods on contaminated Titanium discs

Effect of controlled surface roughness and biomimetic coating on titanium implants adhesion to the bone: An experiment animal study