Abstract:The present study sought to demonstrate the swelling behavior of hydrogel-microcarrier composite constructs to inform their use in controlled release and tissue engineering applications. In this study, gelatin methacrylate (GelMA) and GelMA-gelatin microparticle (GMP) composite constructs were three-dimensionally printed, and their swelling and degradation behavior was evaluated over time and as a function of the degree of crosslinking of included GMPs. GelMA-only constructs and composite constructs loaded with GMPs crosslinked with 10 mM (GMP-10) or 40 mM (GMP-40) glutaraldehyde were swollen in phosphate-buffered saline for up to 28 days to evaluate changes in swelling and polymer loss. In addition, scaffold reswelling capacity was evaluated under five successive drying-rehydration cycles. All printed materials demonstrated shear thinning behavior, with microparticle additives significantly increasing viscosity relative to the GelMA-only solution. Swelling results demonstrated that for GelMA/GMP-10 and GelMA/GMP-40 scaffolds, fold and volumetric swelling were statistically higher and lower, respectively, than for GelMA-only scaffolds after 28 days, and the volumetric swelling of GelMA and GelMA/GMP-40 scaffolds decreased over time. After 5 drying-rehydration cycles, GelMA scaffolds demonstrated higher fold swelling than both GMP groups while also showing lower volumetric swelling than GMP groups. Although statistical differences were not observed in the swelling of GMP-10 and GMP-40 particles alone, the interaction of GelMA/GMP demonstrated a significant effect on the swelling behaviors of composite scaffolds. These results demonstrate an example hydrogel-microcarrier composite system's swelling behavior and can inform the future use of such a composite system for controlled delivery of bioactive molecules in vitro and in vivo in tissue engineering applications. Impact statement In this study, porous three-dimensional printed (3DP) hydrogel constructs with and without natural polymer microcarriers were fabricated to observe swelling and degradation behavior under continuous swelling and drying-rehydration cycle conditions. Inclusion of microcarriers with different crosslinking densities led to distinct swelling behaviors for each biomaterial ink tested. 3DP hydrogel and hydrogel-microcarrier composite scaffolds have been commonly used in tissue engineering for the delivery of biomolecules. This study demonstrates the swelling behavior of porous hydrogel and hydrogel-microcarrier scaffolds that may inform later use of such materials for controlled release applications in a variety of fields including materials development and tissue regeneration.

Swelling under Constraints: Exploiting 3D‐Printing to Optimize the Performance of Gel‐Based Devices

Strong and Ultra-Tough Supramolecular Hydrogel Enabled by Strain-Induced Microphase Separation

Unconstrained dynamic gel swelling generates transient surface deformations

A NURBS-based Inverse Analysis of Swelling Induced Morphing of Thin Stimuli-Responsive Polymer Gels

An energy-optimization method to study gel-swelling in confinement

Swelling kinetics of constrained hydrogel spheres

Effect of confinement on the mechanics of a swelling hydrogel bead

Mechanical and Dimensional Stability of Gelatin-Based Hydrogels Through 3D Printing-Facilitated Confined Space Assembly

Anomalous Mechanical Strengthening of Nanocomposite Hydrogels Upon Swelling

Three-dimensional Shape Transformations of Hydrogel Sheets Induced by Small-Scale Modulation of Internal Stresses

Programmed Deformations of 3d‐printed Tough Physical Hydrogels with High Response Speed and Large Output Force

Constrained Swelling and Instability of A Temperature-Sensitive Hydrogel Ring

Inhomogeneous swelling of a gel in equilibrium with a solvent and mechanical load

4D-Printed Hydrogel Actuators through Diffusion-Path Architecture Design

The swelling and shrinking of spherical thermo-responsive hydrogels

Accelerating the Stimuli-Responsive Bending of a Gel Using Mechanical Constraints

Swelling Behaviors of 3D Printed Hydrogel and Hydrogel-Microcarrier Composite Scaffolds

Spatially and Reversibly Actuating Soft Gel Structure by Harnessing Multimode Elastic Instabilities

Under pressure: Hydrogel swelling in a granular medium

Swelling-strengthening hydrogels by embedding with deformable nanobarriers

Dynamic swelling performance of hydrophobic hydrogels