Abstract:This study investigates how different sodium silicate SiO2/Na2O MS ratios (0.75, 0.9, and 1.2) affect the hydration behavior of amorphous wollastonitic hydraulic (AWH) binders containing various amounts of Al2O3 content (4, 7, 10, and 12%wt). The effects of and interaction between the MS ratio of the activator and the Al2O3 content of the sample on the hydration reaction and paste performance were investigated. The reaction was followed by calorimetry, and the pastes' compressive strength performances were tested at different curing times (2, 7, and 28 days). The hydrated pastes were characterized by FTIR, thermogravimetry analysis, and X-ray diffraction. The calorimetric results show that a higher Al2O3 cContent and a higher MS ratio result in a longer induction period. In terms of paste performance, an increase of the Al2O3 coupled with an activation with a 1.2 MS ratio results in a lower compressive strength after 28 days of hydration; the results range from 76 to 52 MPa. A decrease of the MS ratio to 0.9 allowed the obtention of a narrower range of results, from 76 to 69 MPa. Even though a decrease of the MS ratio to 0.75 led to higher hydration kinetics and high compressive strength results at early ages, at 28 days of curing, a decrease in compressive strength was observed. This may be a consequence of the fast kinetic of the mixture, since the rapid growth of hydration products may inhibit the dissolution at later ages and increase the porosity of the paste. Moreover, the high Al intake in the hydration product, facilitated by the high sodium content of the activator, promotes the formation of a higher number of calcium aluminate silicate hydrate structures (C-A-S-H) to the detriment of calcium silicate hydrate structures (C-S-H), decreasing the compressive strength of the samples. The TGA results indicate that the samples hydrated with the MS075 solution resulted in a higher number of hydrated products at early ages, while the samples hydrated with the MS09 and MS1.2 solutions exhibit a steady increase with curing time. Hence, an equilibrium in the hydration kinetic promoted by Si saturation-undersaturation appears to be fundamental in this system, which is influenced by both the MS ratio and the Al(OH)4- content in solution. The results of this study suggest that for this type of binder, optimal performance can be achieved by decreasing the MS ratio to 0.9. This composition allows for a controlled kinetic and overall higher compressive strength results in pastes produced with this AWH precursor.

Effect of Complex Modifier on Properties of Heat-Hardened Sodium Silicate-Bonded Sand for Castings Production

Molecular simulation and experimental characterization of the effect of hydroxides on the properties of hot hardening sodium silicate bonded ceramic sand

Parametric optimization of modifiers for ester-hardened sodium silicate bonded sand

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

"Materials Studio" Simulation Study of the Adsorption and Polymerization Mechanism of Sodium Silicate on Active Silica Surface at Different Temperatures

Effects of water and carbon dioxide pressure on the adhesion of Na2SiO3 and K2SiO3 binders on silica sand surface: Comparison of experimental data and molecular dynamics simulation

Effect of Carbon Dioxide Temperature on Adhesion of Na2SiO3 Binder to Silica Sand Surface: Comparison of Experimental Data with Molecular Dynamics Simulations

Effect of Additives on Heat Hardened Inorganic Solid Foundry Binder

Enhance of strengthening phase and chemical bonding in bamboo scrap/magnesium oxychloride composites by sodium silicate

Effect of Modifiers on Properties of No-bake Aluminium Phosphate Sand

Effect of Magnesium-containing Modifier on the Properties of Boron Aluminum Phosphate Inorganic Binder and Its Heat-cured Molding Sand

Materials Studio simulation for the adsorption properties of CO2 molecules at the surface of sodium silicate and potassium silicate solution under different pressure conditions

Effect of Particle Size of Quartz Sand Filler on Microstructure and Strength of Alkali-Activated Slag-Based Materials

Wettability, adhesive performance and structural evolution of an environment-friendly modified silicate binder for foundry moulding and coremaking

Influence of Silica Modulus on the Activation of Amorphous Wollastonitic Hydraulic Binders with Different Alumina Content: Study of Hydration Reaction and Paste Performance

The Influence of Various Matrixes on the Strength Properties of Moulding Sands with Thermally Hardened Hydrated Sodium Silicate for the Ablation Casting Process

Properties of a Modified Inorganic Sodium Phosphate-based Casting Binder

Study on the Storage Stability of High Neutralization Degree Phosphate-Bonded No-Bake Sand

Effect of Sodium Hexafluorosilicate Addition on the Properties of Metakaolin Based Geopolymers Cured at Ambient Temperature

Advanced modeling of compressive strength in silica-modified oil well cement: impact of silicate, aluminate, and hydraulic moduli

Influence of Dosage and Modulus on Soluble Sodium Silicate for Early Strength Development of Alkali-Activated Slag Cements