Abstract:The performance of the new generation aero-engine is strongly dependent on the application of integral blisk technologies, while the high-risk failure of integral disk joints severely restricts the promotion of those technologies. Therefore, the molecular dynamics method is used to investigate the influence of nanopores on the tensile properties of single crystal/polycrystalline Ni composites. The results show that the addition of single crystal nickel can increase the tensile strength of single crystal/polycrystalline Ni compared with polycrystalline nickel. The influence of pore position distribution on the tensile properties of single crystal/polycrystalline Ni is investigated. The simulation results show that nanopore defects in a single crystal region significantly aggravate the fracture at the single crystal/polycrystalline Ni interface. Pores not only penetrate the interface of composites but also rapidly expand inside the single crystal and the polycrystalline crystal, in which the interface of composites is further reduced resulting in the failure acceleration of single crystal/polycrystalline Ni composites. On the contrary, when the pores are in a polycrystalline region, the interface of single crystal/polycrystalline Ni hinders the amorphization of the polycrystalline nickel side and inhibits the pores from spreading toward the interface. When the pores are in the interface region, the pores do not continue to expand into the single crystal, but propagate inside the polycrystalline crystal. The effect of the porosity of interface pores on the tensile properties of single crystal/polycrystalline Ni is also discussed. It is found that the tensile strength of single crystal/polycrystalline Ni decreases rapidly when the void porosity exceeds 0.8%. Finally, the influence of the number of voids on the tensile properties while maintaining the porosity of the interface pores is analyzed. When the porosity of the prefabricated pores of the interface is kept constant at 0.8%, the larger the number of pores (i.e., the smaller the pores), the larger the elastic modulus. In the plastic deformation stage, due to the large number of dispersed small pore structures at the interface of the single crystal/polycrystalline Ni composites, the dislocation motion is hindered, which plays a certain strengthening role and improves the tensile strength of the single crystal/polycrystalline Ni composites. It can be concluded that single crystal/polycrystalline Ni with dispersed small pores has better tensile properties than those with large pores.

The Effect of Interatomic Potentials on the Nature of Nanohole Propagation in Single-Crystal Nickel: A Molecular Dynamics Simulation Study

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Solid−Liquid Interfacial Energy and Melting Properties of Nickel under Pressure from Molecular Dynamics

Towards Full Ab Initio Simulations of Mechanical Response of Ti-N Binary System under Extremely Operational Conditions Via Neural Network Potential

Atomistic modeling of crystal-to-amorphous transition and associated kinetics in the Ni-Nb system by molecular dynamics simulations.

Comparison of Interatomic Potentials on Crack Propagation Properties in Bcc Iron

Evaluation of Copper, Aluminum and Nickel Interatomic Potentials on Predicting the Elastic Properties

Effects of crack-γ/γ' interface relative distributions on the deformation and crack growth behaviors of a nickel-based superalloy

Atomistic simulations of the nanoindentation-induced incipient plasticity in Ni3Al crystal

A high-dimensional neural network potential for molecular dynamics simulations of condensed phase nickel and phase transitions

The effect of grain boundary structures on crack nucleation in nickel nanolaminated structure: A molecular dynamics study

Effects of Stress State, Crack—γ/γ′ Phase Interface Relative Locations and Orientations on the Deformation and Crack Propagation Behaviors of the Ni-Based Superalloy—A Molecular Dynamics Study

Pair vs many-body potentials: influence on elastic and plastic behavior in nanoindentation

Molecular dynamics study of the mechanical behavior of nickel nanowire: Strain rate effects

Experimental and molecular dynamics simulation study of structure of liquid and amorphous Ni62Nb38 alloy

A "Magnetic" Machine Learning Interatomic Potential for Nickel

Molecular Dynamics Simulation of Crack Growth in Mono-Crystal Nickel With Voids and Inclusions

Effect of Nanopores on Tensile Properties of Single Crystal/Polycrystalline Nickel Composites

Neural Network Interatomic Potentials For Open Surface Nano-mechanics Applications

Effects of Strain Rate, Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires: A Molecular Dynamics Simulation

Elastic and Plastic Deformations of Nickel Nanowires under Uniaxial Compression