Abstract:In this study, AISI 904L super austenitic - AISI 317L austenitic stainless steel sheets were successfully welded by laser welding method using six different heat inputs. Welded samples went through 1 h of post-weld heat treatment (PWHT) at 1100 °C and then left to cool at room temperature. The effect of PWHT and welding heat input on surface, texture, microstructure and mechanical properties has been examined. According to the results obtained in the study, it was observed that the weld metal microstructure of the samples welded at the lowest and highest heat input values consisted entirely of austenite (dendritic + interdendritic) grains. With PWHT, Cr23C6 precipitation was observed in both grain boundaries and austenite grains. In addition, austenite as well as dislocation and stacking fault formations were observed in the microstructure. While the highest austenite content was observed in the microstructure of AISI 317L, the content of austenite increased in all samples with PWHT. It was observed that most of the grains that were orientated in the [111] direction were orientated in the direction of [101] and [001] after PWHT. However, the KAM values of the dislocation in grain boundaries decreased with the effect of PWHT. In addition, with the reduction of the ratio of dark grains and the effect of re-crystallisation, (112) components representing austenite grains appeared in FCC/BCC texture. It was identified that due to these textural changes, the tensile strength and resistance to bending of the samples were negatively affected but their toughness was positively affected. AB3 sample with the highest tensile strength, hardness, bending strength and lowest toughness had values of 615 MPa, 214 HV, 1100 N and 57 J, respectively, while these values changed to 550 MPa, 181 HV, 720 N and 60 J with the effect of PWHT. Due to the presence of the chromium-oxide layer, it was identified that the density of O− ion and H− ion was at high levels on the surface of the weld metal. It was identified that the density of these ions decreases with increasing depth, while Fe−, Cr− and Ni− ions increase. Excellent K–S and N–W orientation relationship (OR) was observed between FCC/BCC-structured grains present in the microstructure of without PWHT base metals and weld metal, while Bain OR was also observed in weld metal with or without PWHT. In the microstructure of the base metals with PWHT, there was no OR relationship between grains with FCC/BCC structures.

Effect of heat input on mechanical and metallurgical properties of AISI 304L stainless steel by using TIG welding

The effect of heat input on weld-bead geometry, mechanical, phase transformation temperature, and corrosion properties of autogenous double pulse TIG welded nitinol sheets

Effect of Heat Input on Hydrogen Embrittlement of TIG Welded 304 Austenitic Stainless Steel

Effects of heat input on the mechanical properties of butt-welded high and ultra-high strength steels

Effects of heat input on microstructure evolution, mechanical and corrosion properties of TC4 alloy by keyhole TIG welding

The Effect of Welding Current and Electrode Force on the Heat Input, Weld Diameter, and Physical and Mechanical Properties of SS316L/Ti6Al4V Dissimilar Resistance Spot Welding with Aluminum Interlayer

Effects of post-weld heat treatment on dissimilar laser welded joints of austenitic stainless steel to low carbon steel

Effect of Welding Heat Input and Post-weld Thermal Aging on the Sensitization and Pitting Corrosion Behavior of AISI 304L Stainless Steel Butt Welds

Heat treatment and heat input effects on the dissimilar laser beam welded AISI 904L super austenitic stainless steel to AISI 317L austenitic stainless steel: Surface, texture, microstructure and mechanical properties

Effect of TIG welding parameters on 316L stainless steel joints using taguchi L27 approach

Metallurgical and Corrosion Characterization of Austenitic Stainless Steel Welds during Post Weld Heat Treatment

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Effect of heat input on the mechanical and metallurgical aspects of double-pulse MIG welded IN 617

Influence of M-TIG and A-TIG Welding Process on Microstructure and Mechanical Behavior of 409 Ferritic Stainless Steel

Influence of austenitizing temperature on microstructure and mechanical properties of AISI 431 martensitic stainless steel electron beam welds

Effect of post-weld heat treatment on the microstructure and properties of titanium/304 stainless steel laser welding dissimilar metal joints with copper as the transition layer

Effect of post weld heat treatment on metallurgical and mechanical properties of electron beam welded AISI 409 ferritic steel

Mechanical and micro-structural studies of pulsed and constant current TIG weldments of super duplex stainless steels and Austenitic stainless steels

Effect of Ultrasonic Treatment on Residual Stress and Mechanical Properties of AISI 304 Stainless Steel Welding

Effect of heat treatment into tensile strength, hardness and microstructural attributes of TIG welded Ti-6Al-4V titanium alloy

Thermal Effect of Welding on Mechanical Behavior of High-Strength Steel