Abstract:The shape memory behavior of smart materials is widely used for stimulation or shape-shifting purposes. Shape memory polymers (SMPs) can shape and force recoveries accompanied by attractive attributes such as biocompatibility, biodegradability, and universality. In this paper, a thermoplastic elastomer (TPE) is used as a complementary material for 4D printed polylactic acid (PLA) structures to enhance their shape and force recovery properties and lower the stimulation temperature for more practical implementations. Two approaches are followed to provide SMP composites (SMPCs): multi-layered and multi-material lattices. In multi-layered lattices, specimens are comprised of separate layers and different ratios of SMP and TPE materials. For comparison, PLA-TPE filaments with the same ratios of multi-layered lattices are produced and used to fabricate multi-material lattices. Dynamic mechanical thermal analysis tests showed a reduction in the glass transition temperature of the manufactured PLA-TPE filament. X-ray diffraction test was conducted to prove that the crystallinity of the developed PLA-TPE material increases which explains the better shape memory effect in the multi-material specimens. Phase separation occurred in low ratios of TPE in PLA, discernible in field emission scanning electron microscope (FESEM) images, resultting in low quality in one of the developed PLA-TPE filaments. FESEM images also showed proper miscibility of TPE in PLA in higher ratios. Thermomechanical tests were done on printed specimens to examine and compare the shape and force recovery of the produced SMPCs. While the shape recovery of multi-material samples was not as good as multi-layered samples, both approaches have better shape recovery results than the PLA sample. Due to a lower glass transition temperature in multi-material lattices, their shape recovery process started at lower temperatures widening their potential practical applications. Force recovery of multi-material samples revealed a significant improvement which was due to more oriented crystalline polymer structures.

Fabrication of 3D Printed Polylactic Acid/Polycaprolactone Nanocomposites with Favorable Thermo-Responsive Cyclic Shape Memory Effects, and Crystallization and Mechanical Properties

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Crystallization Behavior and Mechanical Properties of Poly(Epsilon-Caprolactone)/Cyclodextrin Biodegradable Composites

Manipulation of Non-Isothermal Crystallization Kinetics of Poly(lactic Acid) Composite Film by a Novel Nucleating Agent

Synergistic effects of cellulose nanocrystals‐organic montmorillonite as hybrid nanofillers for enhancing mechanical, crystallization, and heat‐resistant properties of three‐dimensional printed poly(lactic acid) nanocomposites

Preparation and characterization of 4D printable PCL/SEBS‐g‐MAH blends with excellent mechanical and shape memory properties

3D printing thermo-responsive shape memory polymer composite based on PCL/TPU blends

4D printed TPU/PLA/CNT wave structural composite with intelligent thermal-induced shape memory effect and synergistically enhanced mechanical properties

Temperature and Infill Density Effects on Thermal, Mechanical and Shape Memory Properties of Polylactic Acid/Poly(ε-caprolactone) Blends for 4D Printing

4D printing of PLA/PCL shape memory composites with controllable sequential deformation

Temperature and Infill Density Effects on Thermal, Mechanical and Shape Memory Properties of Polylactic Acid/Poly(-caprolactone) Blends for 4D Printing

Enhancing the mechanical properties of biodegradable PLLA/PBAT blends for 3D filament via one-pot synthesized CNCs-PVAc powder

Shape memory performances of homogeneous poly(L-lactide-co-ε-caprolactone)/polytrimethylene carbonate-grafted functionalized graphene oxide nanocomposites

Synergistic Effects of Polyethylene Glycol and Cellulose Nanofibers on the Isothermal and Non-isothermal Crystallization Behaviors of Polylactide

A novel PLA/P(3HB-co-4HB)/MWCNT composite featuring enhanced mechanical properties and excellent thermal stability based on elongational rheology

Enhancing shape memory properties of multi-layered and multi-material polymer composites in 4D printing

4D printing of semi-crystalline crosslinked polymer networks with two-way shape memory effect

Development of Shape Memory Polylactic Acid/Ethylene-Butyl Acrylate-Maleic Anhydride (PLA/EBA-MAH) Blends for 4D Printing Applications

Prediction of The Mechanical Behavior of Polylactic Acid Parts with Shape Memory Effect Fabricated by FDM

Mechanical Properties and Non-Isothermal Crystallization Kinetics of Polylactic Acid Modified by Polyacrylic Elastomers and Cellulose Nanocrystals

Synthesis and characterization of shape memory poly (ε-caprolactone) networks with programmable and reconfigurable shape-morphing behaviors