Abstract:While lean Mg-Zn-Ca alloys are promising materials for temporary implants, questions remain on the impact of Zn and Ca. In this context, the precipitation in Mg-1.5Zn-0.25Ca (ZX20, in wt.%) was investigated upon linear heating from about room temperature to 400 C, with a particular focus on the debated ternary precipitate phase. Three exothermic differential scanning calorimetry (DSC) peaks were observed at 125, 250 and 320 C. The microstructure at the end of these peaks (205, 260 and 350 C) was probed in a multiscale correlative approach using atom probe tomography (APT) and transmission electron microscopy (TEM). At 205 C, APT analysis revealed Ca-rich, Zn-rich and Zn-Ca-rich clusters of about 3 nm in size and with a number density of 5.7 x 10^23 m^-3. At 260 C, APT and TEM showed mono-layered Zn-Ca-rich Guinier-Preston (GP) zones of about 8 nm in size and with a number density of 1.3 x 10^23 m^-3. At 350 C, there are larger, highly coherent elongated precipitates of about 50 nm in size, in a lower number density, and of two types: either binary Mg2Ca precipitates or less numerous ternary Ca2Mg6Zn3 precipitates, as deduced from scanning TEM-based energy dispersive X-ray spectrometry (EDS) and nanodiffraction in TEM. The highest hardening, probed by Vickers testing, relates to the end of the 125 C DSC peak and thus to GP zones, which outperform the hardening induced by the nanoscale clusters and the larger intermetallic particles. Precipitation in ZX20 upon linear heating was compared to the one induced by hot extrusion at 330 C. Here, ternary precipitates outnumber the binary ones and are larger, incoherent, and in a much lower number density. They are unequivocally made of hexagonal Ca2Mg5Zn5, as deduced by atomically resolved EDS mapping and scanning TEM imaging, and supported by simulations. Precipitation complexity of in lean Mg-Zn-Ca alloys and its kinetic path are discussed.

Partitioning of Ca to metastable precipitates in a Mg-rare earth alloy

Partitioning of Ca to metastable precipitates in a Mg-rare earth alloy

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Early stages of precipitation and microstructure control in Mg–rare earth alloys

The Hydriding and Dehydriding Properties of Some Multicomponent Rare-Earth Magnesium Alloys

Effects of trace Ca addition on microstructure and mechanical properties of as-cast Mg-Sm-Gd-based alloy

Effect of Ca Concentration on Microstructure and Mechanical Properties of As-Cast and As-Extruded Quasicrystal-Strengthened Mg-7.2Zn-2.4Gd Alloy

Precipitation in lean Mg-Zn-Ca alloys

Physical factors controlling the observed high-strength precipitate morphology in Mg–rare earth alloys

The effect of alloy composition on the microstructure and tensile properties of binary Mg-rare earth alloys

Effect of Rare Earth and Ca Micro-Alloying on the Microstructure and Anisotropy of AZ31 Magnesium Alloy Sheets

Effect of rare earth element on amorphization and deformation behavior of crystalline/amorphous dual-phase Mg alloys

Study on the Strengthening Mechanism of Rare Earth Ce in Magnesium Alloys, Based on First-Principle Calculations and Electronegativity Theory

The effects of Ca on the microstructure, mechanical and corrosion properties of extruded Mg-2Zn-0.5Mn alloy

Effect of Addition of Sn on High-Temperature Tensile Strength of Rare-Earth Free Mg-1Ca Alloy

Effect of Calcium on the Rate of Grain Boundary Migration in Pure Magnesium During Annealing

Effect of Ce/La Microalloying on Microstructural Evolution of Mg-Zn-Ca Alloy During Solution Treatment

Influence of Mg Contents on Aging Precipitation Behavior of Al–3.5Cu–xMg Alloy

Effect of Substituting Nd for Y on Microstructure and Mechanical Properties of Mg-7Y-2Al Alloy

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effect of Ca Content on the Mechanical Properties and Corrosion Behaviors of Extruded Mg–7Li–3Al Alloys