Abstract:Offshore oil field loose sandstone reservoirs have high permeability. However, during the water injection process, water injection blockage occurs, causing an increase in injection pressure, making it impossible to continue injecting water on site. Current research mainly focuses on the factors causing water injection blockage, with less attention given to the blockage locations and the pressure increase caused by water injection. There is a lack of research on the change in the law of injection capacity. This paper establishes a simulation experiment for water injection blockage that can accommodate both homogeneous and heterogeneous cores. The experimental core is 1 m long and capable of simulating the blockage conditions in the near-well zone during water injection, thereby analyzing the core blockage position and blockage pressure. The study clarifies the influence of water quality indicators, heterogeneity, and core length on the blockage patterns in reservoirs during water injection. The research findings are as follows: I. The reservoir blockage samples were characterized using scanning electron microscopy (SEM), casting thin sections, and X-ray diffraction (XRD) analysis. The results indicate that the main factors causing blockage are clay, silt, and fine particulate suspensions, with the fine particles mainly consisting of hydrated silicates and alkali metal oxides. The primary cause of blockage in loose sandstone is identified as the mechanism of migration and accumulation of clay, fine rock particles, and suspended matter in the injected water. II. By monitoring pressure and permeability changes in the core flooding experiments, the impact of reservoir heterogeneity on water injection capacity was evaluated. The evaluation results show that the blockage locations and lengths in heterogeneous cores are twice those in homogeneous cores. III. For heterogeneous reservoirs, if the initial permeability at the inlet is lower than in other segments of the core, significant blockage resistance occurs, with the final resistance being 1.27 times that of homogeneous cores. If the initial permeability at the inlet is higher than in other parts, the final blockage resistance is close to that of homogeneous cores. This study provides theoretical support for the analysis of blockage locations and pressures in loose sandstone water injection and offers technical support for the design of unplugging ranges and pressures after blockage in heterogeneous formations. At the same time, it provides a theoretical basis for selecting the direction of acidizing after blockage occurs in loose sandstone.

Research on Optimization of Water Quality Index System for Low Permeability Reservoir Water Injection Development

The injection capacity evaluation of high-pressure water injection in low permeability reservoir: numerical and case study

Research on the Water Injection Pressure Reducing and Increasing Injection System for Low Permeability Reservoirs in Fushan Oilfield

EVALUATION AND RECOMMENDED INDEXES FOR THE ULTRA-LOW PERMEABILITY RESERVOIR DAMAGE BY THE MICROBILE IN THE INJECTED WATER

Laboratory Study on the Water Flooding Development of Bei 301 Block in Hailaer Basin

Intelligent Monitoring and Controlling Technology of Water Injection in Ultra-low Permeability Reservoir of Ordos Basin

Study on Parameters Optimization and Adaptation of Nitrogen Foam Flooding in Reservoirs with High Water Cut and High Permeability

Experimental analysis of acidizing in Weizhou X low permeability reservoir

Study on Damage Mechanism of Waterflooding Development in Weizhou 11-4N Low-Permeability Oilfield

Technology of Water Injection Development in Ultra-Low Permeability Reservoir

Optimization of CO2 immiscible injection incomplex low permeability reservoir

A New Method for Ultra-Low Permeability Reservoir Characterization After Water Flooding Development

Application Practice for Low Environmental Impact Deep Acidizing Process to Improve Injection Capacity of Water Injection Wells

A Numerical Study on Long-Term Water Injection Procedure and the Corresponding Formation Property Variation

Study on the EOR Technique by Immiscible Gas Injection in Wenmi Oilfield of Tuha

THE PH VALUE OPTIMIZATION OF MODIFIED INJECTION WATER IN LIN-NAN OILFIELD

Experimental Evaluation of Blockage Resistance and Position Caused by Microparticle Migration in Water Injection Wells

Integrated Design Technology of Geological Engineering for Pressure Flooding and Water Injection in Low Permeability Reservoirs: Take the Reservoir of Keshang Formation in Wu2 East Area as an Example

Evaluation of the Compatibility Between Formation and Injection Water in Ultra-Low Permeability Reservoirs

Practice and cognition of effective water-flooding development mode in Gaotaizi block of ultra-low permeability reservoir

Analysis of the channeling of water injection in low permeability reservoirs with interlayer considering the seepage–stress coupling