Abstract:The efficient near-infrared response of light-active materials is one of the prerequisites for the most advanced organic solar cells (OSCs). Two benzodithiophene fused-ring cores (BT-4T and DBT-4T), featured with stepwise enlarged conjugations and improved electron-donor characteristics, are designed and used as the central donor units for the construction of acceptor–donor–acceptor-type molecules ZB8 and ZB10. The significantly enhanced intramolecular charge transfer endows ZB8- and ZB10-based OSCs with a photoelectronic response over 1000 nm. With more favorable molecular energy levels and an asymmetric configuration, ZB8-based best OSCs afford a 12.30% power conversion efficiency, better than that of 11.08% for the ZB10-based one. Our successful exploration for electron-rich fused-ring cores provides a quite rare but promising platform for highly efficient OSCs with a photoelectronic response over 1000 nm.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00092.Description of the experimental measurements and instruments; molecular synthesis and characterization; device fabrication and optimization conditions; the calculation method of energy loss; dipole moments of ZB8 and ZB10; cyclic voltammetry plots of ZB8 and ZB10 films; normalized absorption and PL spectra of ZB8 and ZB10 neat films; EQEEL of the devices based on PCE10:ZB8 and PCE10:ZB10; UV–vis absorption spectra of the blend films of PCE10:ZB8 and PCE10:ZB10; electron and hole mobilities of optimized devices; 2D GIWAXS patterns and scattering profiles for ZB8 and ZB10 neat films; and NMR and HR-MS spectra (PDF)This article has not yet been cited by other publications.

Computational optimization and optical analysis of thin-film organic solar cells for high efficiency

Light Management for Fullerene-Based Semitransparent Polymer Solar Cells with a Distributed Bragg Reflector

Fine Optimization of Morphology Evolution Kinetics with Binary Additives for Efficient Non-Fullerene Organic Solar Cells

Efficient Organic Solar Cells with Polymer-Small Molecule: Fullerene Ternary Active Layers

Overcoming Space‐Charge Effect for Efficient Thick‐Film Non‐Fullerene Organic Solar Cells

Designing efficient materials for high-performance of non-fullerene organic solar cells through side-chain engineering on DBT-4F derivatives by non-fused-ring electron acceptors

Optimizing Microstructure Morphology and Reducing Electronic Losses in 1 Cm2 Polymer Solar Cells to Achieve Efficiency over 15%

Organic Solar Cell Optimizations

Design and Optimization of High Performance P3HT: PCBM Polymer Solar Cell Using P3HT Buffer Layer

Optimization Of Processing Solvent And Film Morphology To Achieve Efficient Non-Fullerene Polymer Solar Cells Processed In Air

Individual Nanostructure Optimization in Donor and Acceptor Phases to Achieve Efficient Quaternary Organic Solar Cells

Efficient Ternary Organic Solar Cells Enabled by the Integration of Nonfullerene and Fullerene Acceptors with a Broad Composition Tolerance

Unveiling Excitonic Dynamics in High-Efficiency Nonfullerene Organic Solar Cells to Direct Morphological Optimization for Suppressing Charge Recombination.

Conjugated Extension of Non-Fullerene Acceptors Enables Efficient Organic Solar Cells with Optoelectronic Response over 1000 nm

Optimization of the Active Layer Thickness for Inverted Ternary Organic Solar Cells Achieves 20% Efficiency with Simulation

Precise Control of Hole Transport Layer Integration on PDTS-DTTFBT: PC71BM Organic Solar Cells

Alkyl Chain Tuning of Non-fullerene Electron Acceptors toward 18.2% Efficiency Binary Organic Solar Cells

The role of structural parameters on efficiency and transparency of semi-transparent non-fullerene organic solar cell

Tuning the optoelectronic properties for small organic compounds as organic solar cell applications

Designing Thickness-Insensitive Cathode Interlayers via Constructing Noncovalently Conformational Locks for Highly Efficient Non-fullerene Organic Solar Cells

Efficient Multilayer Organic Solar Cells Using the Optical Interference Peak