Abstract:This study presents a novel synthesis route for high-entropy alloys (HEAs) and high-entropy metallic glass (HEMG) using radio frequency (RF) magnetron sputtering and controlling the HEA phase selection according to atomic size difference (δ) and film thickness. The preparation of HEAs using sputtering requires either multitargets or the preparation of a target containing at least five distinct elements. In developing HEA-preparation techniques, the emergence of a novel sputtering target system is promising to prepare a wide range of HEAs. A new HEA-preparation technique is developed to avoid multitargets and configure the target elements with the required components in a single target system. Because of a customizable target facility, initially, a TiZrNbMoTaCr target emerged with an amorphous phase owing to a high δ value of 7.6, which was followed by a solid solution (SS) by lowering the δ value to 5 (≤6.6). Thus, this system was tested for the first time to prepare TiZrNbMoTa HEA and TiZrNbMoTa HEMG via RF magnetron sputtering. Both films were analyzed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy, field emission scanning electron microscopy cross-sectional thickness, and atomic force microscopy (AFM). Furthermore, HEMG showed higher hardness 10.3 (±0.17) GPa, modulus 186 (±7) GPa, elastic deformation (0.055) and plastic deformation (0.032 GPa), smooth surface, lower corrosion current density (Icorr), and robust cell viability compared to CP-Ti and HEA. XRD analysis of the film showed SS with a body-centered cubic (BCC) structure with (110) as the preferred orientation. The valence electron concentration [VEC = 4.8 (<6.87)] also confirmed the BCC structure. Furthermore, the morphology of the thin film was analyzed through AFM, revealing a smooth surface for HEMG. Inclusively, the concept of configurational entropy (ΔSmix) is applied and the crystalline phase is achieved at room temperature, optimizing the processing by avoiding further furnace usage.

A novel alloy design for non-equiatomic high-entropy alloy (Cr–Fe–Ni–Ti–Nb): predicting entropy mix and enthalpy mix

High Entropy Alloys: Laboratory to Industrial Attempt

Non-equiatomic high entropy alloys: Approach towards rapid alloy screening and property-oriented design

Novel Alloy Design Concepts Enabling Enhanced Mechanical Properties of High Entropy Alloys

Design of Eutectic High Entropy Alloys

Low neutron cross-section FeCrVTiNi based high-entropy alloys: design, additive manufacturing and characterization

Microstructural evolution and phase selection during solidification of AlCrCuFeNi high entropy alloy

Alloy Design and Properties Optimization of High-Entropy Alloys

Designing novel AlCoCrNi eutectic high entropy alloys

Alloy Design Strategies and Future Trends in High-Entropy Alloys

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Ways to improve the properties of high-entropy alloys Cantor CoCrFeNiMn and CoCrFeNiAl

High-Entropy Alloys – A New Era of Exploitation

The application of EET in high-entropy alloy

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Design and Development of High-Entropy Alloys with a Tailored Composition and Phase Structure Based on Thermodynamic Parameters and Film Thickness Using a Novel Combinatorial Target

Design of non-equiatomic medium-entropy alloys

High Entropy Alloys Mined From Phase Diagrams

Exploring the Compositional Space of High-Entropy Alloys for Cost-Effective High-Temperature Applications

Theory-guided design of high-strength, high-melting point, ductile, low-density, single-phase BCC high entropy alloys

Towards high-entropy alloys with high-temperature corrosion resistance and structural stability