Abstract:An equiatomic CoCrFeMnNi high-entropy alloy, which crystallizes in the face-centered cubic (fcc) crystal structure, was produced by arc melting and drop casting. The drop-cast ingots were homogenized, cold rolled and recrystallized to obtain single-phase microstructures with three different grain sizes in the range 4–160μm. Quasi-static tensile tests at an engineering strain rate of 10−3s−1 were then performed at temperatures between 77 and 1073K. Yield strength, ultimate tensile strength and elongation to fracture all increased with decreasing temperature. During the initial stages of plasticity (up to ∼2% strain), deformation occurs by planar dislocation glide on the normal fcc slip system, {111}〈110〉, at all the temperatures and grain sizes investigated. Undissociated 1/2〈110〉 dislocations were observed, as were numerous stacking faults, which imply the dissociation of several of these dislocations into 1/6〈112〉 Shockley partials. At later stages (∼20% strain), nanoscale deformation twins were observed after interrupted tests at 77K, but not in specimens tested at room temperature, where plasticity occurred exclusively by the aforementioned dislocations which organized into cells. Deformation twinning, by continually introducing new interfaces and decreasing the mean free path of dislocations during tensile testing (“dynamic Hall–Petch”), produces a high degree of work hardening and a significant increase in the ultimate tensile strength. This increased work hardening prevents the early onset of necking instability and is a reason for the enhanced ductility observed at 77K. A second reason is that twinning can provide an additional deformation mode to accommodate plasticity. However, twinning cannot explain the increase in yield strength with decreasing temperature in our high-entropy alloy since it was not observed in the early stages of plastic deformation. Since strong temperature dependencies of yield strength are also seen in binary fcc solid solution alloys, it may be an inherent solute effect, which needs further study.

Thermoelastic Martensitic Transformation and Shape Memory Effect in [001]-Oriented Single Crystals of High-Entropy Alloy

Stabilization of deformed stress-induced martensite and its effect on shape memory effect in an Fe-Mn-Si-Ni-Co alloy

Physical Factors Controlling Large Shape Memory Effect in FCC ↔ HCP Martensitic Transformation in CrMnFeCoNi High-Entropy-Alloy Single Crystals

Coexistence of strain glass transition and martensitic transformation in highly nickel-rich ferroelastic alloy with large elastocaloric effect

Stress-Free Two-Way Thermoelastic Shape Memory and Field-Enhanced Strain in Ni52mn24ga24 Single Crystals

Martensitic Transformation and Shape Memory Effect of NiCoMnSn High Temperature Shape Memory Alloy

Crystal structure and high-temperature magnetoplasticity in the new Ni–Mn–Ga–Cu magnetic shape memory alloys

Influence of Heat Treatments on Martensitic Transformations and Elastocaloric Effect in Two-Phase (β + γ) NiFeGa Alloys

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

Microstructure and Magnetic Field-Induced Strain of a Ni-Mn-Ga-Co-Gd High-Entropy Alloy

Superelasticity of [0 0 1]-oriented Fe–Mn–Al–Cr–Ni crystals with a negative temperature dependence of transformation stresses

High-temperature Shape Memory Properties of Cu15Ni35Ti25Hf12.5Zr12.5 High-Entropy Alloy

In Situ Observation of Thermoelastic Martensitic Transformation of Cu-Al-Mn Cryogenic Shape Memory Alloy with Compressive Stress

Microstructure, Martensitic Transformation And Superelasticity Of T1(49) (6)N1(45 1)Cu(5)Cr(0 3) Shape Memory Alloy

Stress-free two-way thermoelastic shape memory and field-enhanced strain

Microstructure, Martensitic Transformation and Superelasticity of Ti49.6Ni45.1Cu5Cr0.3 Shape Memory Alloy

Crystal-to-amorphous phase transformation in ternary shape memory alloys

The Effect of the In-Situ Heat Treatment on the Martensitic Transformation and Specific Properties of the Fe-Mn-Si-Cr Shape Memory Alloys Processed by HSHPT Severe Plastic Deformation

Regularities in the Evolution of Thermoelastic Martensitic Transformations during Cooling/Heating in the Free State and under Load of Titanium Nickelide Alloyed with Niobium

Fe–Mn–Si–Cr–Ni Based Shape Memory Alloy: Thermal and Stress-Induced Martensite

Microstructure and Thermoelastic Martensitic Transformation in Ni-Low and -Rich Ni–Ti–Hf–Nb Hightemperature Shape Memory Alloys