Abstract:In this paper, a new technology for on-orbit cold forming of space truss rods is proposed. For the cold roll forming process of asymmetric cross sections of thin strips, the effects of roll gap and roll spacing on the forming of asymmetric cross sections of strips were investigated using ABAQUS simulation + experiments. The study shows the following. When forming a strip with a specific asymmetric cross section, the stresses are mainly concentrated in corners 2/4/6, with the largest strain value in corner 2. With increasing forming passes, when the roll gap is 0.3 mm, the maximum equivalent strain values are 0.09, 0.24, 0.64 sequentially. Roll gaps of 0.4 mm and 0.5 mm equivalent strain change amplitude are relatively similar, and their maximum equivalent strain values are approximately 0.07,0.15, 0.44. From the analysis of the stress-strain history of the characteristic nodes in corners 2/4/6, it can be seen that the stress and strain changes in the deformation process mainly occur at the moment of interaction between the upper and lower rollers, where the stress type of node 55786 shows two tensile types and one compressive type, the stress type of nodes 48594 and 15928 shows two compressive and one tensile type, and the strain of the three nodes is in accordance with the characteristics of plane strain. When the roll gap is about 0.4 mm, the forming of the strip is relatively good. With increased roll spacing, the strip in the longitudinal stress peak through the rollers shows a small incremental trend, but the peak stresses are 380 Mpa or so. When the roll spacing is 120 mm, the longitudinal strain fluctuation of the strip is the most serious, followed by the roll spacing at 100 mm, and the minimum at 140 mm. Combined with the fluctuation in strip edges under different roll spacings, manufacturing cost and volume and other factors, a roll spacing of 100 mm is more reasonable. It is experimentally verified that when the roll gap is 0.4 mm and the roll spacing is 100 mm, the strip is successfully prepared in accordance with the cross-section requirements. When the rolling gap is 0.3 mm, due to stress-strain concentration, the strip is prone to edge waves in forming. The top of corner 2 of the flange triangular region is susceptible to intermittent tear defects, and the crack extension mechanism is mainly based on the cleavage fracture + ductile fracture.

Research on forming and mechanical properties for one dimensional linear deployable boom Stacer of spacecraft

Structural Analysis for Deployable Space Truss with Twist Springs Activated

Kinematic Analysis and Model Fabrication of a Space Deployable Optical Baffle

Research on the impact on the structural property by rigidization of the inflatable boom

The Application of Shape Memory Polymer Composite in Space Deployable Truss Structure

Research On Structural Form And Mechanical Properties Of The-Suspended Cylindrical Lattice Shells

A Study on the Mechanical Characteristics and Self-Preservation Performance of a Deployment Mechanism with a Large Exhibition Ratio during Its Gathering Process

Mechanical Property Analysis of a Boom-Membrane Structure Used for Aerospace Technologies

Research on Bending Forming Method of Large Diameter-Thickness Ratio Thin-Walled Tubes for Aerospace

Experimental Study and Numerical Simulation of Load-bearing/coiling Characteristics of Thin-walled Lenticular Composite Booms

Driving Force and Blossoming Analysis of a Composite Triangular Rollable and Collapsible (TRAC) Boom Used in Aerospace Technologies

Novel Four-Cell Lenticular Honeycomb Deployable Boom with Enhanced Stiffness

Research Through Design of A One-Dimensional Cable-Rod Deployable Mechanism

Deployment and Blossoming Analysis of a Fiber Reinforced Polymer (FRP) Collapsible Tubular Mast (CTM) Boom for Aerospace Applications

Research on Cold Roll Forming Process of Strips for Truss Rods for Space Construction

Numerical simulation of deployable ultra-thin composite shell structures for space applications and comparison with experiments

Study on the stability of space sleeve stretching arm in the transition stage on non-continuous rigid surfaces based on scale optimization of elastic micro-convex bodies

Manufacturing and mechanical properties of adjustable stiffness hierarchical orthogrid stiffened cylinders

Optimization of Mechanical Properties during Cold Rolling and Wrap-Forming for Metal Helical Tubes

Roll-Out Deployment Process Analysis of a Fiber Reinforced Polymer (FRP) Composite Tape-Spring Boom

Design, Modeling, and Manufacturing of High Strain Composites for Space Deployable Structures