Abstract:The coal industry generated tons of waste over the years of mineral extraction, and the waste disposal leads to soil and air pollution caused by acid mine drainage and spontaneous combustion. Seeking environmental sustainability, this paper investigated the valorization of coal tailings as a primary precursor in geopolymer mortar. The effect of Portland cement as a hardened admixture was evaluated on the mechanical and physical properties of geopolymer mortar, by replacing the coal tailings with a lower amount of Portland cement. Six mortars were characterized by several standard tests besides ultrasonic pulse velocity, mercury porosimetry (MIP), and drying shrinkage, the microstructure was evaluated by SEM/EDS analysis and X-Ray diffraction. The workability was slightly higher for geopolymer mortars with calcium by almost 5%, and the addition of sugarcane molasses and flue gas desulfurization increased the fluidity, reaching 220 mm. The Portland cement improved the early strength of geopolymer mortar by almost 10 MPa at 7 days, due to the acceleration of chemical reaction yielding a denser and heterogeneous matrix. The SEM/EDS analysis evidenced the co-existence of the polymeric matrix and C-A-S-H gel. The compressive strength at 28 days was higher than 20 MPa for all geopolymer mortars. A higher reaction rate provided by calcium addition leads to higher densification of the aluminosilicate matrix at early ages. The ultrasonic pulse velocity (UPV) confirmed denser matrix formation, and the geopolymer with 05 wt% of Portland cement presented UPV of 2700 m/s at 07 days, while the non-calcium geopolymer showed 2000 m/s. The denser matrix formed limited the water loss, decreased the open porosity, and improved the stiffness of geopolymer mortars, yielding a drying shrinkage almost 50% lower than for geopolymer without calcium addition. Finally, this paper established the lower replacement (5 wt%) of coal tailings for Portland cement produced efficient geopolymer mortar, with excellent physical and mechanical properties for in situ application without a thermal cure.

Reaction, structure and properties of eco-friendly geopolymer cement derived from mechanically activated pumice

An Overview of Pumice Stone as a Cementitious Material – the Best Manual for Civil Engineer

Use of pumice stone and silica fume as precursor material for the design of a geopolymer

Mechanical Properties of a Sustainable Low-Carbon Geopolymer Concrete Using a Pumice-Derived Sodium Silicate Solution

Sustainable Utilization of Waste Pumice Powder in Slag-Based Geopolymer Concretes: Fresh and Mechanical Properties

Cement kiln dust-based geopolymer: Microstructural investigation and performances optimization through response surface methodology

Physico-Mechanical Properties and Hydration Processes of Cement Pastes Modified with Pumice, Trass and Waste Chalcedonite Powder

Mechanical behavior and microstructure evolution of slag-fly ash based geopolymer stabilized sand

Preparation and curing method of red mud-calcium carbide slag synergistically activated fly ash-ground granulated blast furnace slag based eco-friendly geopolymer

Enhancing Compressive Strength of Phosphogypsum-Based Geopolymer Cement with Five Alkaline Activator Combinations

Improving the Characteristics of Less Active Geopolymer Binders Utilizing Ground Granulated Blast-Furnace Slag under Different Curing Conditions

Alkali activators with different cations transforming low-value volcanic ash into eco-friendly geopolymers

Preparation and properties of geopolymer containing phosphoric acid-activated fly ash and mechanically-milled kaolinite: Experiments and density function theory

Life cycle assessment (LCA) and the influence of alkaline activator content on mechanical and microstructural properties of geopolymer mortar

Study on the Mechanical Properties, Microstructure and Hydration Mechanism of Phosphogypsum-Based Geopolymer Cement with Added Micron-Sized Silica Particles

Drying shrinkage behavior of geopolymer mortar based on kaolinitic coal gangue

Synthesis and Performance Evaluation of Nano-Calcium Carbonate-Modified Geopolymers Incorporating Fly Ash and Manganese Slag: A Comprehensive Investigative Study

Mechanical behaviour and permeability of geopolymer mortars

Mechanical and durability analysis of geopolymer concrete incorporating bauxite residue, phosphogypsum, and ground granulated blast slag

An efficient approach for sustainable fly ash geopolymer by coupled activation of wet-milling mechanical force and calcium hydroxide

Abrasion Resistance and Microstructural Properties of Sustainable Geopolymer Mortar Produced with Hybrid Blends of GGBFS and Various Earth Materials