Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Using Dispersed Gas Fluid Flow for Cooling of Energy Stressed Elements of Tokamak Structure

Cooling a Surface Exposed to a High Thermal Load by a Dispersed Flow

Turbulent Heat Transfer for Coolant Water Flow in Plasma Facing Component

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Numerical Simulation of Heat Transfer and Fluid Flow of a Non-Equilibrium Argon Plasma Jet with Confined Wall

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Preliminary Design of Water-Cooling System for Liquid Metal Divertor Target Test Module in EAST

Thermal Design of High-Power DC Reactor for ITER Poloidal Field Converter

Development of a Complex for Materials Science Studies on the T-15MD Tokamak

Physics of the low momentum diffusivity regime in tokamaks and its experimental applicability

Conceptual design study for heat exhaust management in the ARC fusion pilot plant

Optimization Analysis for Structure of Cooling Channel of Fusion Reactor Divertor

Calculation of in-situ steady-state heat flux on EAST lower divertor

The Plasma-Facing Materials of Tokamak Thermonuclear Reactors: Requirements, Thermal Stabilization, and Tests (a Review)

Critical heat flux analysis of divertor cooling flow channel in fusion reactor with cfd method

Optimal Thermal-Hydraulic Performance for Helium-Cooled Divertors

Analyses of Monoblocks Divertor at One-Sided High Heat Flux Using RPI Wall Boiling Model

Cooling Circuit Development of Equatorial Diagnostic Port Plug Dedicated to International Thermonuclear Experimental Reactor

Numerical simulation of a blanket cooling system for fusion reactor based on PWR conditions

Multiscale simulation of rarefied gas flows in Divertor Tokamak Test facility