Abstract:Carbon steels are widely used in the production of automobiles, bridges, plates, and so on because of their superior mechanical properties and low cost. Carbon steels contain various types of microstructures such as ferrite, pearlite, and martensite, and desired mechanical properties can be obtained by combining these microstructures. While carbon steels exhibit excellent mechanical properties, their pitting corrosion resistance is relatively low in chloride-containing environments. Although the steels are successfully protected from corrosion by coating and/or painting, localized corrosion is readily initiated at cut edges and in coating defect areas in atmospheric environments. To prolong their service life and improve their reliability, it is necessary to elucidate the initiation mechanism of pitting corrosion on carbon steels. While it is widely known that the microstructures of carbon steels affect their corrosion resistance, the detailed mechanism is still unclear. The objective of this research is to clarify the relationship between the microstructure and pitting corrosion resistance of carbon steels in chloride-containing near-neutral pH environments. The pitting corrosion resistance of the typical microstructures of carbon steels was investigated using a micro-electrochemical polarization technique. Various microstructures (ferrite, pearlite, tempered martensite, decarburized martensite, as-quenched martensite etc.) were obtained by conducting different heat-treatments, and micro-scale electrodes (ca. 100 μm × 100 μm) were prepared with only one microstructure included. Small areas without any non-metallic inclusions were chosen as the micro-scale electrodes to eliminate the effect of pit initiation at the inclusion and evaluate the intrinsic corrosion behavior of the microstructure itself. Then, potentiodynamic anodic polarization measurements were carried out in NaCl-containing boric-borate buffers at pH 8.0. It was determined that the pitting corrosion resistance depends on the type of microstructure, with the as-quenched martensite showing the highest pitting corrosion resistance. The as-quenched martensite includes a high amount of interstitial C in the Fe lattice, and it was also clarified that the anodic dissolution of steels was clearly suppressed with increasing interstitial C content. During pitting corrosion, the local breakdown of the passive film is induced by chloride ions, which results in the initiation of active dissolution. It was considered that the low dissolution rate provided by interstitial C results in the superior pitting corrosion resistance of as-quenched martensite. To clarify the reason for the superior active dissolution resistance obtained by interstitial C, first-principles calculations were conducted. At first, the electronic structure of martensite was analyzed using bulk-model supercells with bct Fe crystal structures which included interstitial C. According to first-principles calculations, the electronic density of states (DOS) at and around the Fermi level decreased due to the presence of interstitial C. In addition, a valence electron transfer occurred from Fe to C atoms, resulting in a decrease in the number of valence electrons of Fe. Because the presence of valence electrons at and around the Fermi level affects the kinetics of electron (charge) transfer in oxidation/reduction reactions, including the active dissolution reaction, it was considered possible that the presence of interstitial C suppressed the electronic reactivity of Fe. Furthermore, first-principles calculations were also carried out for slab-model supercells consisting of a metal/vacuum interface, and the effect of interstitial C on the work function of martensite was analyzed. The result of the calculations indicated the work function of martensite linearly increased with increasing interstitial C content. Since the work function and ionization energy of metals are the same, the electrochemical properties of metals, such as dissolution resistance, are considered to be principally associated with their work function. In other words, it is understood that metals with a high work function are associated with a higher dissolution resistance. According to the above calculation results, the change in the electronic structure of Fe and the increase in the work function provided by interstitial C are key factors contributing to the superior dissolution resistance of martensite.

Effect of quenching in aqueous polyvinylpyrrolidone solutions on the microstructure and pitting corrosion resistance of AISI 1045 carbon steel

(Corrosion Division Morris Cohen Graduate Student Award) Microscopic Electrochemical Properties of Carbon Steels and Metallurgical Approach for High Corrosion Resistance

Effect of Microstructure on Corrosion Resistance of Ultralow‐Carbon Bainitic Steel

Effect of Tempered Martensite and Ferrite/Bainite on Corrosion Behavior of Low Alloy Steel Used for Flexible Pipe Exposed to High-Temperature Brine Environment

The corrosion behavior of low carbon steel (AISI 1010) influenced by grain size through microstructural mechanical

Repassivation-oriented pitting corrosion analysis in a cause-effect relationship with microstructure, precipitation, and mechanical behavior of low-carbon medium-chromium ferritic stainless steel

Effect of Tensile Deformation on Microstructure and Corrosion Resistance of High Nitrogen Austenitic Stainless Steels

Direct observation of pitting corrosion evolutions on carbon steel surfaces at the nano-to-micro- scales

Effects of Cooling Rate on the Precipitation Behavior of Grain Boundary Carbide and Corrosion Resistance of 5cr15mov Stainless Steel

Influence of Cooling Rate on Microstructure Evolution and Pitting Corrosion Resistance in the Simulated Heat-Affected Zone of 2304 Duplex Stainless Steels

Effect of Dissolved Oxygen on Pitting Corrosion Behavior of Low-Alloy Steel under Hydrostatic Pressure

Effects of austenitizing temperature on the microstructure and electrochemical behavior of a martensitic stainless steel

Microstructure Evolution and Pitting Corrosion Resistance of the Gleeble-Simulated Heat-Affected Zone of A Newly Developed Lean Duplex Stainless Steel 2002

Influence of Thermomechanical Treatments on Corrosion of Carbon Steel in Synthetic Geopolymer Fly Ash Pore Solution

The effect of microstructure of an advanced duplex stainless steel on the pitting corrosion and chloride-induced stress corrosion cracking resistance

Research on Pitting Corrosion of Micro-alloyed High Strength Steel Bars

The effect of microstructure on the initial corrosion behavior of low carbon steel in simulated coal solution

Effects of quenching temperature on bainite transformation, retained austenite and mechanical properties of hot-galvanized Q&P steel

Effect of quenching and tempering on microstructure and corrosion resistance of aerospace-bearing steel

The Microstructure and Corrosion Behavior of Cr-containing Ferrite-Pearlite Steels in an Acidic Environment

Effect of cooling rate on microstructure and mechanical properties of a low-carbon low-alloy steel