Abstract:With the further development of intelligent robots, bionic touch sensing has become an important means for the robotic dexterous hand to interact with the external environment, making it a hot topic. However, in the existing research on tactile perception of robotic hands, most of the sensing units have complex structures and are difficult to integrate in the hand. For touch sensing of the dexterous robot hand, this work employs optical Fiber Bragg Grating(FBG)as the information transmission and sensing carrier and develops a wearable touch fingerstall. The thumb fingerstall contains two segments:fingertip and finger pulp. The fingertip is composed of a curved surface and a plane surface. The curved surface can fit the thumb shape better, and the plane surface can provide a more stable touch. Specially, we use a cylindrical pin as the knuckle to connect the fingertip and finger pulp. The touch sensing of three contact positions of the fingerstall have been studied: position 1 is the vertical fingertip, position 2 is the 15 degrees fingertip, and position 3 is the 30 degrees finger pulp. Firstly, the fingerstall model was simulated using the finite element method to verify its structural feasibility. Then, the fingerstall was loaded using an electronic tension machine, ranging from 0 N to 10 N with a 1 N increment, and each load was held for 25 s. For each test position, the experiment was repeated three times, and the responses of FBG were recorded. Analysis of the touch sensing experimental data shows that the sensing fingerstall has good sensitivity and linearity within the 0 similar to 10 N touch pressure range. The average sensitivities at position 1, position 2, and position 3 are 24.119 6 pm/N, 10.338 3 pm/N, and - 1.580 7 pm/ N, respectively, with linearity above 99%. Overall, the simulation results are basically consistent with the experimental results, although some errors may arise due to 3D printing and FBG packaging. Therefore, different loading positions and forces can be distinguished by different center wavelength offset and offset direction of FBG. In order to verify the sensing performance of the fingerstall further, a hardness discrimination experiment was carried out primarily focused on perceiving objects of small hardness. And the standard ratio of wavelength to touch depth (k(s)) was proposed as a quantitative measure of hardness perception. Position 1 was selected as the experimental position for hardness perception, and four silicone blocks with different hardness (named as 0 HA, 10 HA, 20 HA and 40 HA) were selected as the experimental objects. Considering the time and safety factors, 5 mm was selected as the touching depth, and 60mm/ min as the touching speed. The average responses of FBG to 0 HA, 10 HA, 20 HA and 40 HA are 58.57 pm, 242.3 pm, 580.95 pm, 1107.6 pm, respectively. The corresponding k(s) values are 11.717 pm/mm, 48.46 pm/mm, 116.19 pm/mm and 221.52 pm/mm, respectively. According to the data results, when the fingerstall touches the 40 degrees silicone block, the k(s) is the largest, and the k(s) is the smallest at the 0 degrees silicone block. When k(s) is larger, the greater the hardness of the object is. The sensing fingerstall has a good repetition, with repeatability errors of 3.82%, 0.97%, 0.51%, and 0.29%.In conclusion, a simple and wearable fingerstall has been designed. The tactile sensitivity of three different position has been studied, and a hardness discrimination experiment has been conducted. These research results can serve as a basis for bionic touch sensing of dexterous robotic hands.

FBG Tactile Sensing System Based on GAF and CNN

Research on FBG Tactile Sensing Shape Recognition Based on Convolutional Neural Network

Fiber Bragg grating tactile perception system based on cross-modal transformer

Optical Fibre Bragg Based Sliding-tactile Sensing and Classification Training Method for Material Recognition

A Skin-Inspired PDMS Optical Tactile Sensor Driven by a Convolutional Neural Network

Machine Learning-Assisted Dual Fiber Bragg Grating-Based Flexible Direction Sensing

Variable Stiffness Object Recognition with a CNN-Bayes Classifier on a Soft Gripper

Soft 2D tactile sensor based on fiber Bragg gratings and machine learning algorithms

Recognition of surface texture with wearable tactile sensor array: A pilot Study

Fault-Tolerant Six-Axis FBG Force/Moment Sensing for Robotic Interventions

Soft Bionic Skin With Touch-Slip and Thermal Perception Using Double-Layer Distributed FBG Sensing Array

A Bio‐Inspired Artificial Tactile Sensing System Based on Optical Microfiber and Enhanced by Neural Network

Gradient adaptive sampling and multiple temporal scale 3D CNNs for tactile object recognition

Bionic Touch Sensing of Wearable Fingerstall Based on Optical Fiber Bragg Grating

Research on Convex Fiber Grating Tactile Sliding Sensor Based on Mechanical Fingers

On the integration of FBG sensing technology into robotic grippers

Tactile-GAT: tactile graph attention networks for robot tactile perception classification

Flexible Arc-Shaped Micro-Fiber Bragg Grating Array Three-Dimensional Tactile Sensor for Fingertip Signals Detection and Human Pulse Monitoring

Fruit recognition and classification based on tactile information of flexible hand

Feedforward Neural Network for Force Coding of an MRI-Compatible Tactile Sensor Array Based on Fiber Bragg Grating

Multi-Fingered In-Hand Manipulation with Various Object Properties Using Graph Convolutional Networks and Distributed Tactile Sensors