Abstract:In this study, the influence of silicon nitride (Si 3 N 4 ) and zirconia (ZrO 2 ) ceramics was examined on the titanium alloy using the pulsed electric current sintering technique to investigate the microstructural behavior, densification, and nanomechanical properties of these composites. Si 3 N 4 and ZrO 2 were dispersed in Ti-6Al-4 V at a functional pressure of 50 MPa, a sintering temperature of 1200 °C, a heating rate of 100 °C/min, and a holding time of 10 min. The ternary composite samples were prepared viz, Cs1 (Ti6Al4V- 3 vol.% Si 3 N 4 - 15 vol.% ZrO 2 ), Cs2 (Ti6Al4V- 3 vol.% Si 3 N 4 - 10 vol.% ZrO 2 ), and Cs3 (Ti6Al4V- 3 vol.% Si 3 N 4 - 5 vol.% ZrO 2 ). The bulk morphology of the composites was studied using scanning electron microscopy (SEM) equipped with EDS, and the phase contents were identified with an X-ray diffractometer (XRD). The relative density results for the tri-composites showed that the Cs1 sample recorded the highest at 99.94%, producing a fully dense sintered composite. However, there was a drop in the relative density of composites Cs2 and Cs3, recording 97.73% and 97.11%, respectively, comparable to the unreinforced Ti-6Al-4 V alloy with 98.65%. The nanoindentation examination conducted for the trio-composites showed linear mechanical responses/improvement, with Vickers hardness, from 589.31 to 865.70 MPa; nano hardness, from 6.466 to 9.441 GPa, and elastic modulus, from 113.52 to 185.95 GPa.

Microstructural and nanoindentation study of TaN incorporated ZrB2 and ZrB2–SiC ceramics

Fabrication of (Zr,Ti)B2-ZrN-BN composites through reactive spark plasma sintering of ZrB2 and TiN

Influence of TiN addition on densification behavior and mechanical properties of ZrB2 ceramics

A TEM study of nanostructures and interfaces in the hot-press sintered ZrB2–SiC–Si3N4 composites

The impact of Si3N4 incorporation on the mechanical characteristics of ZrB2-SiC nanocomposite sintered via pressureless method

Microstructures and Enhanced Mechanical Properties of (Zr, Ti)(C, N)-Based Nanocomposites Fabricated by Reactive Hot-Pressing at Low Temperature

Microstructural evolution and mechanical properties of in situ nano Ta4HfC5 reinforced SiBCN composite ceramics

Influence of TiB2 and CrB2 on densification, microstructure, and mechanical properties of ZrB2 ceramics

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

Novel (Zr, Ti)B2-(Zr, Ti)C-SiC ceramics via reactive hot pressing

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

Densification, microstructure, and nanomechanical evaluation of pulsed electric sintered zirconia-silicon nitride reinforced Ti-6Al-4 V alloy

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

β→α Phase Transformation and Properties of Solid-State-Sintered SiC Ceramics with TaC Addition

Sintering Behavior, Microstructure and Mechanical Properties of Silicon Carbide Ceramics Containing Different Nano-Tin Additive

A microstructural approach to the chemical reactions during the spark plasma sintering of novel TiC–BN ceramics

Effects of Ti on the Microstructural Evolution and Mechanical Property of the SiBCN-Ti Composite Ceramics

Microstructure and mechanical properties of SiC composite ceramics modified by (TixZr1–x)B2 solid solution

Characterization of Ceramic Microstructure and Nanoindentation under Different Loads

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase