Abstract:Abstract One of the challenges in the transfer of heat during the mechanical machining process is the coolant substance used in the internal cooling method which is generally liquid water or a water-based coolant. This limits the heat transfer capacity insofar as the thermal conductivity of liquid water is concerned. The other difficulty is the requirement for an external mechanical system to pump the coolant around the internal channel, providing efficient transfer of the accumulated thermal energy. This study proposes a novel method to address this issue by using liquid gallium which provides the means to transfer the excess heat generated during the cutting process by integrating the design into an aluminium oxide insert. Combining this with a magnetohydrodynamic drive, the coolant system operates without the need for mechanical input. Liquid gallium is nontoxic and has a much higher thermal conductivity over liquid water. Investigations of the novel cooling system is performance compared against liquid water through numerical modelling, followed by an experimental machining test to ascertain the difference in heat transfer effectiveness, tool wear rates and workpiece surface finish when compared to dry machining and external cooling conditions on stainless steel 316L. Without cooling, experimental machining tests employing a cutting speed of V c = 250 m min −1 resulted in a corner wear VB c rate of 75 μm, and with the magnetohydrodynamic-based coolant on, produced a VB c rate of 48 μm, indicating a difference of 36% in relative tool wear under the same cutting conditions. Increasing the cutting speed V c to 900 m min −1 , produced a corner wear VB c rate of 357 μm without the active coolant and a VB c rate of 246 μm with the magnetohydrodynamic-based coolant on, representing a decrease of 31% in relative tool wear. Further tests comparing external liquid water cooling against the liquid gallium coolant showed at V c = 250 m min −1 , a difference of 29% in relative tool wear rate reduction was obtained with the internal liquid gallium coolant. Increasing the cutting speed to V c = 900 m min −1 , the data indicated a difference of 16% relative tool wear reduction with the internal liquid gallium. The results support the feasibility of using liquid gallium as an internal coolant in cutting inserts to effectively remove thermal energy.

Short communication: Experiment study on micro-textured tool with internal cooling

Ultrasonic Elliptical Vibration Texturing of the Rake Face of Carbide Cutting Tools for Adhesion Reduction

Coupling effect of micro-textured tools and cooling conditions on the turning performance of aluminum alloy 6061

Comparative study of dry machining performance using hybrid textured cutting insert

Investigation on Cutting Performance of Micro-Textured Cutting Tools

Improving the frictional properties of the tool/chip interface of micro-textured ceramics tools by using electromagnetic-assisted nanofluids

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Research on cutting lubrication performance of textured tools considering slip boundary conditions

Effect of Derivative Cutting of Flank-Faced Textured Ceramic Tools on Machined Surface

Effect of micro-textured morphology with different wettabilities on tool cutting performance

Experimental study of EDM milling of 3D-shaped diffuser for film cooling holes on turbine blades

Experimental Study and Parameter Optimization on Sustainable and Efficient Machining GH4169 with Rotating Short Arc Milling Method

Experimental Study on Chip Shape and Tool Wear of High-Speed and Micro-Feed Cutting

Tool wear evolution and its influence on cutting performance during milling ultra-high-strength steel using different cooling conditions

Experimental investigation of micro-pillar textured WC inserts during turning of Ti6Al4V under various cutting fluid strategies

Investigation of the Material Removal Mechanism in Electrochemical Discharge Drilling Using a High-Speed Rotating Helical Tool-Electrode

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Study on magnetohydrodynamic internal cooling mechanism within an aluminium oxide cutting tool

Study on the effect of texture on cutting performance of the coated tool with finite element analysis and experimental method

Study on force-thermal characteristics of ball end milling cutter with chamfered edge and micro-textured flank face

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode