Yuze Ye Qingsong He Changli Yang Xiaodong Xu Lin Xie Diyi Liu Bo Zeng Zhijian Leng a Jiangsu Key Laboratory of Bionic Materials and Equipment,College of Mechanical and Electrical Engineering,Nanjing University of Aeronautics and Astronautics,Nanjing,Chinab Key Laboratory of Advanced Technology for Small and Medium-Sized UAV,Ministry of Industry and Information Technology,Unmanned Aerial Vehicles Research Institute,Nanjing University of Aeronautics and Astronautics,Nanjing,Chinac State Key Laboratory of Mechanics and Control of Aerospace Structures,Nanjing University of Aeronautics and Astronautics,Nanjing,Chinad Laboratory of Aerospace Servo Actuation and Transmission,Beijing Institute of Precision Mechatronics and Controls,Beijing,Chinae Technology Center,CCCC Second Harbor Engineering Company,Wuhan,China

Abstract:Hydraulic electrostatic actuators have become a research hotspot for their inherent flexibility and safety of human-machine interaction. This paper aims to combine the characteristics of dielectric elastomers and fluid actuators, enhancing the dielectric constant and breakdown field strength by modifying Al 2 O 3 on the surface of nanostructured BaTiO 3 and in order to develop a hydraulic electrostatic actuator with silicone rubber as the matrix material. Single-factor experiments were firstly conducted to confirm the range of three factors affecting the actuation strain of the actuator: BaTiO 3 @Al 2 O 3 content, thickness of the silicone rubber elastomer film, and pre-stretching ratio coefficient. The response surface methodology was used to study the interactive influence of the above three influencing factors on the actuation strain. It was obtained that A has an insignificant influence on the actuation strain, AB has a significant influence on the actuation strain, and B , C , AC , and BC have a highly influence on the actuation strain. Maximizing actuation strain as the optimization objective yielded the combination results of each factor: BaTiO 3 @Al 2 O 3 content of 2.57%, thickness of 0.60 mm, and pre-stretching ratio coefficient of 2.50. Actuation strain tests were conducted with optimized parameters under no-load. The experimental results of the actuation strain test show that the relative error between the test value and the model prediction value of 16.47% is less than 5%, and the optimization model results are reliable. The optimized hydraulic electrostatic actuator was tested for actuation strain and electrical performance under different loads. The experiment showed that the maximum actuation strain of the hydraulic electrostatic actuator was 17.20% under a load of 100 g. The critical breakdown current of the actuator ranged from 115 μA to 130 μA, and the maximum electromechanical conversion efficiency of the actuator under different loads was 67.93%. Finally, a joint actuating device was developed based on the structure of the actuator, amplifying the output displacement of the actuator to 30 mm, and the linear displacement of the soft electro-fluid actuator can be converted into a 20° rotation angle through the gear steering mechanism, thus validating the effectiveness of the hydraulic electrostatic actuator.

Development of a dual magnetostrictive material rods–based electro-hydrostatic actuator

Development of Vibratory Stress Relief Actuators Based on Giant Magnetostrictive Materials

Optimization Design of Giant Magnetostrictive Micro High-Speed Valve Actuator

The Design of High-speed Powerful Actuator Based on Giant Magnetostrictive Material and Analysis of Its Dynamic Modeling

Development of a magnetostrictive material–based electro-hydrostatic actuator with an active rotary rectifying valve

Conceptual design of self-sensing actuator based on giant magnetostrictive material

Design, Modeling and Simulation of an Innovation Pneumatic High Speed On-off Valve Based on Giant Magnetostrictive Material

Development of an Ε-Type Actuator for Enhancing High-Speed Electro-Pneumatic Ejector Valve Performance

Experimental Research on Output Performances of Giant Magnetostrictive Actuator

Design and Control of an Electrohydraulic Soft Actuator System for Robotic Grippers

Research on position control of bidirectional dual magnetostrictive rods-based electro-hydrostatic actuator with active rotary valve

Characteristic investigations on magnetic field and fluid field of a giant magnetostrictive material-based electro-hydrostatic actuator

Low Power Linear Actuator for Direct Drive Electrohydraulic Valves

Novel Bidirectional Linear Actuator for Electrohydraulic Valves

Motor-Driven Giant Magnetostrictive Actuator

Modeling and Performance Analysis of a Magnetorheological Fluid Actuation System

Design and Identification of a Double-Acting Piezoelectric-Hydraulic Hybrid Actuator

Development of a deflector-jet electrohydraulic servovalve using a giant magnetostrictive material

Novel Bidirectional Rotary Proportional Actuator for Electrohydraulic Rotary Valves

Development of a large flow electro-hydrostatic actuator equipped with four magnetostrictive-actuated pumps

Optimized design and performance testing of hydraulic electrostatic actuator